 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DATA SHEET MOS INTEGRATED CIRCUIT PD17145(A1), 17147(A1), 17149(A1) SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS The PD17145(A1), 17147(A1), and 17149(A1) are 4-bit single-chip microcontrollers integrating an 8-bit A/D converter (4 channels), a timer function (3 channels), and a serial interface. These microcontrollers employ a CPU of the general-purpose register type that can execute direct memory operations and direct memory-to-memory data transfer for efficient programming. All the instructions consist of 16 bits per word. In addition, a one-time PROM version, the PD17P149, is also available for program evaluation. The functions of these microcontrollers are described in detail in the following User's Manual. Be sure to read the following manual when designing your system: PD17145 Subseries User's Manual: IEU-1383 FEATURES * 17K architecture * Program memory (ROM) : General-purpose register type : Instruction length fixed to 16 bits : PD17145(A1) : 2 KB (1024 x 16 bits) : PD17147(A1) : 4 KB (2048 x 16 bits) : PD17149(A1) : 8 KB (4096 x 16 bits) * Data memory (RAM) * External interrupt * Instruction execution time * 8-bit A/D converter * Timer * Serial interface * POC circuit (mask option) * Operating voltage * Operating temperature : VDD = 2.7 to 5.5 V (at 400 kHz to 2 MHz) : VDD = 4.5 to 5.5 V (at 400 kHz to 8 MHz) : Ta = -40 to +110 C : 110 x 4 bits : 1 (INT pin, with sense input) : 2 s (at 8 MHz: ceramic oscillation) : 4 channels, absolute accuracy: 1.5 LSB MAX. (VDD = 4.0 to 5.5 V) : 3 channels : 1 channel (clocked 3-wire) APPLICATIONS Automotive electronics, etc. Unless contextually excluded, references in this data sheet to the PD17149 (A1) mean the PD17145 (A1) and PD17147 (A1). The information in this document is subject to change without notice. Document No. U13233EJ1V1DS00 (1st edition) (Previous No. IC-3580) Date Published January 1998 N CP(K) Printed in Japan (c) 1995 PD17145(A1), 17147(A1), 17149(A1) ORDERING INFORMATION Part Number Package 28-pin plastic shrink DIP (400 mil) 28-pin plastic SOP (375 mil) 28-pin plastic shrink DIP (400 mil) 28-pin plastic SOP (375 mil) 28-pin plastic shrink DIP (400 mil) 28-pin plastic SOP (375 mil) Quality Grade Special Special Special Special Special Special PD17145CT(A1)-xxx PD17145GT(A1)-xxx PD17147CT(A1)-xxx PD17147GT(A1)-xxx PD17149CT(A1)-xxx PD17149GT(A1)-xxx Remark xxx indicates ROM code suffix. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Corporation to know the specification of quality grade on the devices and its recommended applications. 2 PD17145(A1), 17147(A1), 17149(A1) FUNCTION LIST Part Number PD17145 (A1) Item ROM capacity RAM capacity Stack 2 KB (1024 x 16 bits) 110 x 4 bits PD17147 (A1) 4 KB (2048 x 16 bits) PD17149 (A1) 8 KB (4096 x 16 bits) Address stack x 5, interrupt stack x 3 * I/O : 20 :2 Note I/O ports 23 * Input * Sense input (INT pin ) :1 A/D converter input 4 channels (shared with port pins), absolute accuracy: 1.5 LSB MAX. * 8-bit timer/counter: 2 channels (can be used as 1 channel of 16-bit timer) Timer 3 channels * 7-bit basic interval timer: 1 channel (can be used as watchdog timer) Serial interface 1 channel (3-wire) * Multiple interrupt by hardware (3 levels MAX.) * External interrupt (INT): 1 Rising edge, falling edge, or both rising and falling edges selectable for detection. Interrupt * Internal interrupt: 4 * Timer 0 (TM0) * Timer 1 (TM1) * Basic interval timer (BTM) * Serial interface (SIO) Instruction execution time Standby function POC circuit 2 s (at 8 MHz, ceramic oscillation) HALT, STOP Mask option (Can be used in application circuit that operates on VDD = 5 V 10 %, 400 kHz to 4 MHz) 2.7 to 5.5 V (at 400 kHz to 2 MHz) Operating voltage 4.5 to 5.5 V (at 400 kHz to 8 MHz) 28-pin plastic shrink DIP (400 mil) Package 28-pin plastic SOP (375 mil) One-time PROM version Quality grade is "standard" and not (A1). Operating temperature range: Ta = -40 to +85 C PD17P149 Note The INT pin is used as an input pin (sense input) when the external interrupt function is not used. The status of this pin is read by using the INT flag of a control register, not by a port register. Caution The PROM version is functionally compatible with the mask ROM versions but its internal circuit and part of the electrical characteristics are different from those of the mask ROM versions. To replace the PROM version with a mask ROM version, thoroughly conduct application evaluation by using a sample of the mask ROM version. 3 PD17145(A1), 17147(A1), 17149(A1) PIN CONFIGURATION (Top View) 28-pin plastic shrink DIP (400 mil) 28-pin plastic SOP (375 mil) VDD P0F1/VREF P0C3/ADC3 P0C2/ADC2 P0C1/ADC1 P0C0/ADC0 P0B3 P0B2 P0B1 P0B0 P0A3 P0A2 P0A1 P0A0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 GND XIN XOUT RESET INT P0F0/RLS P0D0/SCK P0D1/SO P0D2/SI P0D3/TM1OUT P0E0 P0E1 P0E2 P0E3 PD17145CT(A1) - xxx PD17145GT(A1) - xxx PD17147CT(A1) - xxx PD17147GT(A1) - xxx PD17149CT(A1) - xxx PD17149GT(A1) - xxx ADC0-ADC3 GND INT P0A0 to P0A3 P0B0 to P0B3 P0C0 to P0C3 P0D0 to P0D3 P0E0 to P0E3 RESET RLS SCK SI SO TM1OUT VDD VREF XIN, XOUT : analog input : ground : external interrupt input : port 0A : port 0B : port 0C : port 0D : port 0E : reset input : standby release signal input : serial clock I/O : serial data input : serial data output : timer 1 output : power : A/D converter reference voltage : for system clock oscillation P0F0 and P0F1 : port 0F 4 PD17145(A1), 17147(A1), 17149(A1) BLOCK DIAGRAM VDD Clock Divider fx/2 N System Clock Generator CPU CLOCK CLK STOP XIN XOUT P0A3 P0A2 P0A1 P0A0 P0B3 P0B2 P0B1 P0B0 P0C3/ADC3 P0C2/ADC2 P0C1/ADC1 P0C0/ADC0 RF P0A (CMOS) INT Interrupt Controller RAM 110 x 4 bits SYSTEM REG. IRQTM0 IRQTM1 IRQBTM IRQSIO IRQBTM P0B (CMOS) Basic Interval Timer IRQTM1 ALU fx/2 N P0C (CMOS) Timer 1 IRQTM0 fx/2 N fx/2 N Timer 0 A/D Converter P0F1/VREF P0F Note 1 P0E (N-ch) ROM Instruction Decoder P0E3 P0E2 P0E1 P0E0 P0F0/RLS P0D3/TM1OUT P0D2/SI P0D1/SO P0D0/SCK P0D (N-ch) RESET Program Counter GND Serial Interface TM1 IRQSIO Stack Note 2 Notes 1. The ROM capacity of each product is as follows: 1024 x 16 bits: PD17145(A1) 2048 x 16 bits: PD17147(A1) 4096 x 16 bits: PD17149(A1) 2. The stack capacity of each product is as follows: 5 x 10 bits: PD17145(A1) 5 x 11 bits: PD17147(A1) 5 x 12 bits: PD17149(A1) Remark CMOS or N-ch in ( ) indicate the output format of the port. CMOS : CMOS push-pull output N-ch : N-ch open-drain output 5 PD17145(A1), 17147(A1), 17149(A1) CONTENTS 1. 1.2 1.3 1.4 PIN ..................................................................................................................................... 9 Equivalent Circuit of Pin ............................................................................................................... 11 Handling of Unused Pins .............................................................................................................. 15 Note on Using RESET and P0F0/RLS Pins ............................................................................... 16 1.1. Pin Function ..................................................................................................................................... 9 2. 2.1 PROGRAM MEMORY (ROM) ...................................................................................... 17 Configuration of Program Memory .............................................................................................. 17 3. 3.1 3.2 PROGRAM COUNTER (PC) ....................................................................................... 18 Configuration of Program Counter .............................................................................................. 18 Operation of Program Counter .................................................................................................... 18 4. 4.1 4.2 STACK ........................................................................................................................... 19 Configuration of Stack .................................................................................................................. 19 Stack Function ............................................................................................................................... 19 5. 5.1 DATA MEMORY (RAM) ............................................................................................... 20 Configuration of Data Memory ..................................................................................................... 20 6. 6.1 GENERAL REGISTER (GR)........................................................................................ 21 General Register Pointer (RP) ..................................................................................................... 21 7. 7.1 SYSTEM REGISTER (SYSREG) ................................................................................ 22 Configuration of System Register ............................................................................................... 22 8. 8.1 8.2 REGISTER FILE (RF) .................................................................................................. 24 Configuration of Register File ...................................................................................................... 24 Function of Register File .............................................................................................................. 25 9. 9.1 9.2 DATA BUFFER (DBF) ................................................................................................. 26 Configuration of Data Buffer ........................................................................................................ 26 Function of Data Buffer ................................................................................................................ 27 10. ALU BLOCK .................................................................................................................. 28 10.1 Configuration of ALU Block .......................................................................................................... 28 11. PORTS ........................................................................................................................... 30 11.1 Port 0A (P0A0, P0A1, P0A2, P0A3) .............................................................................................. 30 11.2 Port 0B (P0B0, P0B1, P0B2, P0B3) .............................................................................................. 31 11.3 Port 0C (P0C0/ADC0, P0C1/ADC1, P0C2/ADC2, P0C3/ADC3) ................................................... 32 11.4 Port 0D (P0D0/SCK, P0D1/SO, P0D2/SI, P0D3/TM1OUT) ........................................................ 33 11.5 Port 0E (P0E0, P0E1, P0E2, P0E3) .............................................................................................. 34 11.6 Port 0F (P0F0/RLS, P0F1/VREF) ................................................................................................... 34 6 PD17145(A1), 17147(A1), 17149(A1) 12. 8-BIT TIMERS/COUNTERS (TM0, TM1) ................................................................... 35 12.1 Configuration of 8-Bit Timers/Counters ..................................................................................... 35 13. BASIC INTERVAL TIMER (BTM) ............................................................................... 39 13.1 Configuration of Basic Interval Timer ........................................................................................ 39 13.2 Registers Controlling Basic Interval Timer ............................................................................... 41 13.3 Watchdog Timer Function ........................................................................................................... 43 14. A/D CONVERTER ......................................................................................................... 45 14.1 Configuration of A/D Converter .................................................................................................. 45 14.2 Function of A/D Converter ........................................................................................................... 46 14.3 Operation of A/D Converter ........................................................................................................ 47 15. SERIAL INTERFACE (SIO) ......................................................................................... 50 15.1 Function of Serial Interface ......................................................................................................... 50 15.2 Operation Mode of 3-Wire Serial Interface ............................................................................... 52 16. INTERRUPT FUNCTION .............................................................................................. 54 16.1 Types of Interrupt Causes and Vector Addresses ................................................................... 54 16.2 Hardware of Interrupt Control Circuit ......................................................................................... 55 17. STANDBY FUNCTION ................................................................................................. 56 17.1 Outline of Standby Function ....................................................................................................... 56 17.2 HALT Mode ................................................................................................................................... 58 17.3 STOP Mode ................................................................................................................................... 60 18. RESET ............................................................................................................................ 63 18.1 Reset Function .............................................................................................................................. 63 18.2 Reset Operation ........................................................................................................................... 64 19. POC CIRCUIT (MASK OPTION) ................................................................................. 65 19.1 Function of POC Circuit ............................................................................................................... 65 19.2 Conditions to Use POC Circuit ................................................................................................... 66 20. INSTRUCTION SET ...................................................................................................... 67 20.1 Outline of Instruction Set ............................................................................................................. 67 20.2 Legend ........................................................................................................................................... 68 20.3 Instruction Set ............................................................................................................................... 69 20.4 Assembler (AS17K) Embedded Macro Instruction ................................................................... 71 21. ASSEMBLER RESERVED WORDS ........................................................................... 72 21.1 Mask Option Directive .................................................................................................................. 72 21.2 Reserved Symbols ....................................................................................................................... 74 22. ELECTRICAL SPECIFICATIONS ............................................................................... 82 23. CHARACTERISTIC CURVE (REFERENCE VALUE) ............................................... 88 7 PD17145(A1), 17147(A1), 17149(A1) 24. PACKAGE DRAWINGS .................................................................................................... 90 25. RECOMMENDED SOLDERING CONDITIONS .............................................................. 94 APPENDIX A. FUNCTION COMPARISON BETWEEN PD17145 SUBSERIES AND THE PD17135A AND 17137A ...................................................................... 96 APPENDIX B. DEVELOPMENT TOOLS ................................................................................. 98 8 PD17145(A1), 17147(A1), 17149(A1) 1. PIN 1.1. Pin Function Pin Number 1 Symbol VDD Power supply. Reference voltage input to port 0F and A/D converter. * Pull-up resistor can be connected by mask option. * P0F1 * Bit 1 of 2-bit input port (P0F) * VREF * Reference voltage input pin of A/D converter Analog input to port 0C and A/D converter. * P0C3-P0C0 * 4-bit I/O port * Can be set in input or output mode bitwise. * ADC3-ADC0 * Analog inputs to A/D converter. Port 0B. * 4-bit I/O port * Can be set in input or output mode in 4-bit units. * Pull-up resistor can be connected in 4-bit units via software. Port 0A. * 4-bit I/O port. * Can be set in input or output mode in 4-bit units. * Pull-up resistor can be connected in 4-bit units via software. Port 0E. * 4-bit I/O port. * Can be set in input or output mode in 4-bit units. * Pull-up resistor can be connected in 4-bit units via software. Port 0D that is also used for timer 1 output, serial data input, serial data output, and serial clock I/O. * Pull-up resistor can be connected bitwise via software. * P0D3-P0D0 * 4-bit I/O port. * Can be set in input or output mode bitwise. * TM1OUT * Timer 1 output * SI * Serial data input * SO * Serial data output * SCK * Serial clock I/O Function Output Format -- After Reset -- 2 P0F1/VREF Input Input (P0F1) 3 to 6 P0C3/ADC3 to P0C0/ADC0 CMOS push-pull Input (P0C) 7 8 9 10 P0B3 P0B2 P0B1 P0B0 CMOS push-pull Input 11 12 13 14 P0A3 P0A2 P0A1 P0A0 CMOS push-pull Input 15 16 17 18 P0E3 P0E2 P0E1 P0E0 N-ch open-drain Input 19 P0D3/TM1OUT N-ch open-drain Input (P0D) 20 21 22 P0D2/SI P0D1/SO P0D0/SCK 9 PD17145(A1), 17147(A1), 17149(A1) Pin Number Symbol Function Port 0F or standby mode release signal input. * Pull-up resistor can be connected by mask option. * R0F0 * Bit 0 of 2-bit input port (P0F) * RLS * Standby mode release signal input External interrupt request signal input. Also used to release standby mode. * Pull-up resistor can be connected by mask option. System reset input. * Pull-up resistor can be connected by mask option. For system clock oscillation. Connect ceramic resonator across XIN and XOUT. GND Output Format After Reset 23 P0F0/RLS Input Input (P0F0) 24 INT Input Input 25 RESET Input Input 26 27 28 XOUT XIN GND -- -- -- -- 10 PD17145(A1), 17147(A1), 17149(A1) 1.2 Equivalent Circuit of Pin The input/output circuit of each pin is shown below, partially simplified. (1) P0A0 to P0A3 and P0B0 to P0B3 VDD VDD P-ch pull-up flag data Output latch P-ch output disable N-ch Selector Input buffer 11 PD17145(A1), 17147(A1), 17149(A1) (2) P0C0/ADC0 to P0C3/ADC3 VDD data Output latch P-ch output disable N-ch input disable Selector Input buffer A/D converter (3) P0D3/TM1OUT and P0D1/SO VDD pull-up flag data Output latch P-ch output disable N-ch Selector Input buffer 12 PD17145(A1), 17147(A1), 17149(A1) (4) P0D2/SI and P0D0/SCK VDD pull-up flag data Output latch P-ch output disable N-ch Selector Input buffer (5) P0E0 to P0E3 VDD data Output latch P-ch pull-up flag output disable N-ch Selector Input buffer (6) P0F0/RLS VDD Input buffer Mask option stand-by release 13 PD17145(A1), 17147(A1), 17149(A1) (7) P0F1/VREF VDD A/D select Input buffer Mask option A/D end STOP mode VREF P-ch (8) RESET and INT VDD Mask option Input buffer 14 PD17145(A1), 17147(A1), 17149(A1) 1.3 Handling of Unused Pins Handle unused pins as shown in the table below. Table 1-1. Handling of Unused Pins Handling Pin Name Internally P0A, P0B, P0D, P0E Connect on-chip pull-up resistor via software. -- Do not connect on-chip pull-up resistor P0F1 by mask option. Connect on-chip pull-up resistor by mask option. Port P0F0Note 2 Do not connect on-chip pull-up resistor by mask option. Externally Open Connect to VDD via pull-up resistor, or to GND via pull-down resistorNote 1 . Directly connect to VDD or GND. P0C Input mode Open Directly connect to GND. P0A, P0B, P0C (CMOS port) P0D Output mode (N-ch open-drain port) Output low level. -- Open Do not connect pull-up on-chip resistor via software, but output low level. Connect on-chip pull-up resistor via software and output high level. Do not connect on-chip pull-up resistor by mask option. Directly connect to VDD or GND. P0E (N-ch open-drain port) External interrupt (INT) Connect on-chip pull-up resistor by mask option. Open RESET Note 3 (when only internal POC circuit is used) Do not connect on-chip pull-up resistor by mask option. Connect on chip pull-up resistor by mask option. Directly connect to VDD. Notes 1. Take into consideration the drive capability and current dissipation of a port when the port is externally pulled up or down. To pull up or down the port with a high resistance, exercise care so that noise is not superimposed on the port pin. The appropriate value of the pull-up or pulldown resistor differs depending on the application circuit. Generally, select a resistor of several 10 k. 2. 3. The P0F0/RLS pin is also used to set a test mode. When this pin is not used, do not connect a pull-up resistor to it by mask option, but directly connect it to GND. In an application circuit where a high reliability is required, be sure to input the RESET signal from an external source. The RESET pin is also used to set a test mode. When this pin is not used, directly connect it to VDD. Caution It is recommended to fix the input/output mode, pull-up resistor by software, and the output level of the pin by repeatedly setting them in each loop of the program. 15 PD17145(A1), 17147(A1), 17149(A1) 1.4 Note on Using RESET and P0F0/RLS Pins The RESET and P0F0/RLS pins also have a function to set a test mode in which the internal operation of the PD17149(A1) is tested (for IC test only), in addition to the function described in 1.1 Pin Function. If a voltage higher than VDD is applied to these pins, the test mode is set. If a noise higher than VDD is superimposed on these pins during normal operation, therefore, the test mode is set by mistake, affecting normal operation. If the wiring length of the RESET or P0F0/RLS pin is too long, for example, noise may be superimposed on the pin. To prevent this, the wiring length must be kept as short as possible. Otherwise, use a diode or capacitor as shown below. q Connect a low-VF diode between VDD and RESET, P0F0/RLS VDD q Connect a capacitor between VDD and RESET, P0F0/RLS VDD VDD VDD Diode with low VF RESET, P0F0/RLS RESET, P0F0/RLS 16 PD17145(A1), 17147(A1), 17149(A1) 2. PROGRAM MEMORY (ROM) Table 2-1 shows the program memory configuration of the PD17145(A1), 17147(A1), and 17149(A1). Table 2-1. Program Memory Configuration Part Number Program Memory Capacity 2 KB (1024 x 16 bits) 4 KB (2048 x 16 bits) 8 KB (4096 x 16 bits) Program Memory Address 0000H-03FFH 0000H-07FFH 0000H-0FFFH PD17145(A1) PD17147(A1) PD17149(A1) The program memory stores programs and constant data tables. The program memory is addressed by the program counter. Addresses 0000H-0005H are allocated to a reset start address and various interrupt vector addresses. 2.1 Configuration of Program Memory Figure 2-1 shows the program memory map. The program memory is divided in units called "pages" each of which consists of 2K steps with one step made up of 16 bits. Addresses 0000H-07FFH (page 0) of the program memory can be specified by the direct subroutine call instruction. The entire address range of the program memory, 0000H-0FFFH, can be specified by the branch, indirect subroutine call, and table reference instructions. Figure 2-1. Program Memory Map Address 0000H 0001H 0002H 0003H 0004H 0005H Reset start address Serial interface interrupt vector Basic interval timer interrupt vector Timer 1 interrupt vector Timer 0 interrupt vector Page 0 External (INT) interrupt vector CALL addr instruction subroutine entry address BR addr instruction branch address BR @AR instruction branch address CALL @AR instruction subroutine entry address MOVT DBF, @AR instruction table reference address 03FFH (With PD17145(A1)) 07FFH (With PD17147(A1)) Page 1 0FFFH (With PD17149(A1)) 16 bits 17 PD17145(A1), 17147(A1), 17149(A1) 3. PROGRAM COUNTER (PC) The program counter is used to address the program memory. 3.1 Configuration of Program Counter The program counter is a 10-/11-/12-bit binary counter as shown in Figure 3-1. Figure 3-1. Program Counter MSB PC11 PC10 PC9 PC8 PC7 PC6 PC5 PC4 PC3 PC2 PC1 LSB PC0 PC ( PD17145(A1)) PC ( PD17147(A1)) PC ( PD17149(A1)) 3.2 Operation of Program Counter Usually, the contents of the program counter are automatically incremented each time an instruction has been executed. When reset has been effected, when a branch, subroutine call, return, or table reference instruction has been executed, or when an interrupt has been acknowledged, the address of the program memory to be executed next is set to the program counter. Figure 3-2. Value of Program Counter after Instruction Execution Bit of Program Counter Instruction At reset BR addr 1 CALL addr BR @AR CALL @AR (MOVT DBF, @AR) RET RETSK RETI When interrupt is acknowledged Vector address of each interrupt Contents of address stack indicated by stack pointer (return address) Contents of address register (AR) 0 Value specified by addr PC11 PC10 0 0 0 PC9 0 PC8 0 Value of Program Counter PC7 0 PC6 0 PC5 0 PC4 0 PC3 0 PC2 0 PC1 0 PC0 0 Remark The PD17145(A1) does not have PC11 and PC10. The PD17147(A1) does not have PC11. 18 PD17145(A1), 17147(A1), 17149(A1) 4. STACK The stack is a register to which the return address of the program or the contents of the system registers, which are described later, are saved when a subroutine call instruction is executed or when an interrupt is acknowledged. 4.1 Configuration of Stack Figure 4-1 shows the configuration of the stack. The stack consists of a 3-bit binary counter, stack pointer (SP), five 10-bit (PD17145(A1)), 11-bit (PD17147(A1)), or 12-bit (PD17149(A1)) address stack registers (ASRs), and three 5-bit interrupt stack registers (INTSKs). Figure 4-1. Configuration of Stack Stack pointer (SP) b2 SPb2 b1 SPb1 b0 SPb0 0H 1H 2H 3H 4H b11 b10 b9 b8 Address stack registers (ASRs) b7 b6 b5 b4 b3 b2 b1 b0 Address stack register 0 Address stack register 1 Address stack register 2 Address stack register 3 Address stack register 4 SP is initialized to 5H at reset. Interrupt stack registers (INTSKs) 0H BCDSK0 CMPSK0 1H BCDSK1 CMPSK1 2H BCDSK2 CMPSK2 CYSK0 CYSK1 CYSK2 ZSK0 ZSK1 ZSK2 IXESK0 IXESK1 IXESK2 4.2 Stack Function The stack is used to save a return address when the subroutine call or table reference instruction is executed. When an interrupt is acknowledged, the return address of the program and the contents of the program status word (PSWORD) are automatically saved to the stack. After they are saved to the stack, all the bits of PSWORD are cleared to 0. 19 PD17145(A1), 17147(A1), 17149(A1) 5. DATA MEMORY (RAM) The data memory is used to store data for operation and control. Data can always be written to or read from this memory by using an instruction. 5.1 Configuration of Data Memory The data memory is assigned addresses each consisting of 7 bits. The higher 3 bits of an address are called a "row address", while the lower 4 bits are called a "column address". Take address 1AH for example. The row address of this address is 1H and the column address is 0AH. One address consists of 4 bits (= 1 nibble) of memory. The data memory consists of an area to which the user can save data, and areas to which special functions are allocated in advance. These areas are: * System register (SYSREG) * Data buffer (DBF) * Port register (Refer to 7. SYSTEM REGISTER (SYSREG).) (Refer to 9. DATA BUFFER (DBF).) (Refer to 11. PORT.) Figure 5-1. Configuration of Data Memory Column address BANK0 0 0 1 2 3 4 5 6 7 P0A (4 bits) P0B (4 bits) P0C (4 bits) P0D (4 bits) P0E (4 bits) P0F (2 bits) 1 2 3 4 5 6 7 8 9 A B C D E F DBF3 DBF2 DBF1 DBF0 Example : Address 1AH of BANK0 System register 20 PD17145(A1), 17147(A1), 17149(A1) 6. GENERAL REGISTER (GR) As its name implies, the general register is used for general purposes such as data transfer and operation. The general register of the 17K series is not a fixed area, but an area specified on the data memory by using the general register pointer (RP). Therefore, a part of the data memory area can be specified as a general register as necessary, so that data can be transferred between data memory areas and the data in the data memory can be operated with a single instruction. 6.1 General Register Pointer (RP) RP is a pointer that specifies part of the data memory as the general register. RP specifies the bank and row addresses of a data memory area that is to be specified as the general register. Consisting of a total of 7 bits, RP is assigned to 7DH (RPH) and 7EH (RPL), and the higher 3 bits of the system register (refer to 7. SYSTEM REGISTER (SYSREG)). RPH specifies a bank, and RPL specifies a data memory row address. Figure 6-1. Configuration of General Register Pointer Column address BANK0 0 0 1 2 Row addresses 0H to 7H can be 3 Row specified by address general register 4 pointer (RP). 5 6 7 System register RP General register (16 nibbles) General register area when RPH = 0000B, RPL = 010xB 1 2 3 4 5 6 7 8 9 A B C D E F Address Name Symbol Bit 7DH 7EH General register pointer (RP) RPH RPL b3 b2 b1 b0 b3 b2 b1 b0 B C D Data 0 0 0 0 Reset 0 0 0 0 0 0 0 21 PD17145(A1), 17147(A1), 17149(A1) 7. SYSTEM REGISTER (SYSREG) The system register (SYSREG) is a register that directly controls the CPU, and is located on the data memory. 7.1 Configuration of System Register Figure 7-1 shows the location of the system register on the data memory. As shown in this figure, the system register is located at addresses 74H-7FH of the data memory. Because the system register is located on the data memory, it can be manipulated by all the data memory manipulation instructions. It is therefore possible to specify the system register as a general register. Figure 7-1. Location of System Register on Data Memory Column address 0 0 1 1 2 3 4 5 6 7 8 9 A B C D E F Row address 2 3 4 5 6 7 0 Port register 1 2 3 4 5 6 System register (SYSREG) 7 8 9 A B C D E F Data memory (BANK0) Figure 7-2 shows the configuration of the system register. As shown in this figure, the system register consists of the following seven registers: * Address register * Window register * Bank register * Index register * Data memory row address pointer * General register pointer * Program status word (AR) (WR) (BANK) (IX) (MP) (RP) (PSWORD) 22 PD17145(A1), 17147(A1), 17149(A1) Figure 7-2. Configuration of System Register Address 74H 75H 76H 77H 78H 79H 7AH 7BH Index register (IX) Data memory row address pointer (MP) IXH Symbol Bit AR3 AR2 AR1 AR0 WR BANK MPH MPL IXM IXL RPH RPL PSW 7CH 7DH 7EH 7FH Name Address register (AR) Window Bank register register (WR) (BANK) General register pointer (RP) Program status word (PSWORD) b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 Data Note1 0000 Note2 M (IX) 0000P0000 (AR) (BANK) E (MP) 0000 (RP) BCC I CMYZ X DP E Initial Undefivalue at 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ned 0000000000000000000000000000 reset Notes 1. 2. 0 in this field means that the bit is "fixed to 0". b3 and b2 of AR2 of the PD17145(A1) are fixed to 0. b3 of AR2 of the PD17147(A1) is fixed to 0. 23 PD17145(A1), 17147(A1), 17149(A1) 8. REGISTER FILE (RF) The register file is a register that mainly sets the conditions of the peripheral hardware. 8.1 Configuration of Register File 8.1.1 Configuration of register file Figure 8-1 shows the configuration of the register file. As shown in this figure, the register file consists of 128 nibbles (128 x 4 bits). Like the data memory, the register file is assigned addresses in 4-bit units, with row addresses 0H-7H and column addresses 0H-0FH. Addresses 00H-3FH of the register file are called a control register. Figure 8-1. Configuration of Register File Register file 0 1 Row address Column address 0123456789ABCDEF 2 3 4 5 6 7 Control register 8.1.2 Register file and data memory Figure 8-2 shows the relationships between the register file and data memory. As shown in this figure, addresses 40H to 7FH of the register file overlaps the data memory. It seems from the program as if addresses 40H to 7FH of the data memory exist at addresses 40H-7FH of the register file. 24 PD17145(A1), 17147(A1), 17149(A1) Figure 8-2. Relationships between Register File and Data Memory Column address 0 0 1 Data memory 1 2 3 4 5 6 7 8 9 A B C D E F Row address 2 3 4 5 6 7 Port register BANK0 System register 0 1 2 3 Register file Control register 8.2 Function of Register File 8.2.1 Function of register file The register file is a collection of registers that set the conditions of the peripheral hardware by using the PEEK or POKE instruction. The registers that control the peripheral hardware are allocated to addresses 00H-3FH. These registers are called control registers. Addresses 40H-7FH of the register file overlap the ordinary data memory. These addresses can therefore be read or written by not only the MOV instruction but also the PEEK and POKE instructions. 8.2.2 Functions of control registers The control registers are used to set the conditions of the peripheral hardware listed below. For the details of the peripheral hardware and control registers, refer to the description of each peripheral hardware. * Port * 8-bit timers/counters (TM0, TM1) * Basic interval timer (BTM) * A/D converter * Serial interface (SIO) * Interrupt function * Stack pointer (SP) 25 PD17145(A1), 17147(A1), 17149(A1) 9. DATA BUFFER (DBF) The data buffer consists of 4 nibbles allocated to addresses 0CH-0FH of BANK0 of the data memory. This area is a data storage area that transfers data with the peripheral hardware of the CPU (address register, serial interface, timers 0 and 1, and A/D converter) by using the GET or PUT instruction. Moreover, the constants on the program memory can be read to the data buffer by using the MOVT DBF, @AR instruction. 9.1 Configuration of Data Buffer Figure 9-1 shows the location of the data buffer on the data memory. As shown in this figure, the data buffer is allocated addresses 0CH-0FH of the data memory, and consists of a total of 16 bits or 4 nibbles (4 x 4 bits). Figure 9-1. Location of Data Buffer Column address 0 0 1 Row address 2 3 4 5 6 7 System register (SYSREG) Data memory BANK0 1 2 3 4 5 6 7 8 9 A B C D E F Data buffer (DBF) Figure 9-2 shows the configuration of the data buffer. As shown in this figure, the data buffer consists of 16 bits of the data memory, with the bit 0 of address 0FH as the LSB and bit 3 of address 0CH as the MSB. Figure 9-2. Configuration of Data Buffer Data memory BANK0 Address Bit Bit Symbol < 0CH b3 b2 b1 b0 b3 0DH b2 b1 b9 b0 b8 b3 b7 0EH b2 b6 b1 b5 b0 b4 b3 b3 0FH b2 b2 b1 b1 b0 b0 b15 b14 b13 b12 b11 b10 DBF3 M S B Data buffer DBF2 DBF1 DBF0 < Data L S B < Data Because the data buffer is located on the data memory, it can be manipulated by all the data memory manipulation instructions. > 26 PD17145(A1), 17147(A1), 17149(A1) 9.2 Function of Data Buffer The data buffer has two main functions. One is to transfer data with the peripheral hardware, and the other is to read the constant data on the program memory (table reference). Figure 9-3 shows the relationships between the data buffer and peripheral hardware. Figure 9-3. Data Buffer and Peripheral Hardware Data buffer (DBF) Peripheral address Internal bus 01H Peripheral hardware Shift register (SIOSFR) 02H Timer 0 modulo register (TM0M) 03H Program memory (ROM) Constant data 40H Timer 1 modulo register (TM1M) 04H A/D converter data register (ADCR) Address register (AR) Timer 0 timer 1 count register (TM0TM1C) 45H 27 PD17145(A1), 17147(A1), 17149(A1) 10. ALU BLOCK The ALU executes arithmetic and logical operations, bit judgment, and rotation processing of 4-bit data. 10.1 Configuration of ALU Block Figure 10-1 shows the configuration of the ALU block. As shown, the ALU block consists of an ALU that processes 4-bit data, and peripheral circuits such as temporary registers A and B, status flip-flops that control the status of the ALU, and a decimal adjustment circuit that is used when a BCD operation is performed. The status flip-flops are a zero flag FF, carry flag FF, compare flag FF, and BCD flag FF, as shown in Figure 10-1. The status flip-flops correspond to the zero flag (Z), carry flag (CY), compare flag (CMP), and BCD flag (BCD) of the program status word (PSWORD: addresses 7EH, 7FH) on a one-to-one basis. 28 PD17145(A1), 17147(A1), 17149(A1) Figure 10-1. Configuration of ALU Block Data bus Temporary register A Temporary register B Status flip-flop ALU * Arithmetic operation * Logical operation * Bit judgment * Compare judgment * Rotation processing Decimal adjustment circuit Address Name Bit Flag 7EH 7FH Program status word (PSWORD) b0 BCD b3 CMP b2 CY b1 Z b0 IXE Status flip-flop BCD flag FF CMP flag FF CY flag FF Z flag FF Functional Outline Indicates that result of arithmetic operation is 0. Stores carry or borrow resulting from arithmetic operation. Specifies whether result of arithmetic operation is stored. Specifies whether decimal adjustment is performed when arithmetic operation is executed. 29 PD17145(A1), 17147(A1), 17149(A1) 11. PORTS 11.1 Port 0A (P0A0, P0A1, P0A2, P0A3) Port 0A is a 4-bit I/O port with an output latch. It is mapped at address 70H of BANK0 of the data memory. The output format is CMOS push-pull output. This port can be set in the input or output mode in 4-bit units. The input or output mode is specified by P0AGIO (bit 0 of address 2CH) on the register file. When P0AGIO = 0, all the pins of port 0A are set in the input mode. When an instruction that reads the data of the port register is executed at this time, the pin status is read. When P0AGIO = 1, all the pins of port 0A are set in the output mode, and the contents written to the output latch are output to the pins. When an instruction that reads the port status is executed with the port set in the output mode, the contents of the output latch, instead of the pin status, are read. A pull-up resistor can be connected on-chip to this port through software. Whether the pull-up resistor is connected is specified by P0AGPU (bit 0 at address 0CH) of the register file. All the four pins are pulled up when P0AGPU = 1. When P0AGPU = 0, the pull-up resistor is not connected. P0AGIO and P0AGPU are cleared to "0" at reset, and all the P0A pins are set in the input mode without the pull-up resistor connected. The value of the output latch is also cleared to "0". Table 11-1. Writing and Reading Port Register (0.70H) P0AGIO RF: 2CH, bit 0 0 1 Input/Output Mode of Pin Input Output Write Enabled Write to P0A latch BANK0 70H Read P0A pin status P0A latch contents 30 PD17145(A1), 17147(A1), 17149(A1) 11.2 Port 0B (P0B0, P0B1, P0B2, P0B3) Port 0B is a 4-bit I/O port with an output latch. It is mapped at address 71H of BANK0 of the data memory. The output format is CMOS push-pull output. This port can be set in the input or output mode in 4-bit units. The input or output mode is specified by P0BGIO (bit 1 of address 2CH) on the register file. When P0BGIO = 0, all the pins of port 0B are set in the input mode. When an instruction that reads the data of the port register is executed at this time, the pin status is read. When P0BGIO = 1, all the pins of port 0B are set in the output mode, and the contents written to the output latch are output to the pins. When an instruction that reads the port status is executed with the port set in the output mode, the contents of the output latch, instead of the pin status, are read. A pull-up resistor can be connected on-chip to this port through software. Whether the pull-up resistor is connected is specified by P0BGPU (bit 1 at address 0CH) of the register file. All the four-bit pins are pulled up when P0BGPU = 1. When P0BGPU = 0, the pull-up resistor is not connected. P0BGIO and P0BGPU are cleared to "0" at reset, and all the P0B pins are set in the input mode without the pull-up resistor connected. The value of the output latch is also cleared to "0". Table 11-2. Writing and Reading Port Register (0.71H) P0BGIO RF: 2CH, bit 1 0 1 Input/Output Mode of Pin Input Output Write Enabled Write to P0B latch BANK0 71H Read P0B pin status P0B latch contents 31 PD17145(A1), 17147(A1), 17149(A1) 11.3 Port 0C (P0C0/ADC0, P0C1/ADC1, P0C2/ADC2, P0C3/ADC3) Port 0C is a 4-bit I/O port with an output latch. It is mapped at address 72H of BANK0 of the data memory. The output format is CMOS push-pull output. This port can be set in the input or output mode in 1-bit units. The input or output mode is specified by P0CBIO0-P0CBIO3 (address 1CH) on the register file. When P0CBIOn = 0 (n = 0 to 3), the corresponding port pin, P0Cn, is set in the input mode. When an instruction that reads the data of the port register is executed at this time, the pin status is read. When P0CBIOn = 1 (n = 0 to 3), the P0Cn pin is set in the output mode, and the contents written to the output latch are output to the pin. When an instruction that reads the port status is executed with a port pin set in the output mode, the contents of the output latch, instead of the pin status, are read. At reset, P0CBIO0-P0CBIO3 are cleared to "0", setting all the P0C pins in the input mode. The contents of the output latch are also cleared to "0" at this time. Port 0C is also used to input analog voltages to the A/D converter. Whether each pin of the port is used as a port pin or analog input pin is specified by P0C0IDI-P0C3IDI (address 1BH) on the register file. When P0CnIDI = 0 (n = 0-3), the P0Cn/ADCn pin functions as a port pin. When P0CnIDI = 1 (n = 0 to 3), the P0Cn/ADCn pin functions as an analog input pin of the A/D converter. If any of the P0CnIDI (n = 0 to 3) bits is set to "1", the P0F1/VREF pin is used as the VREF pin. When a pin of port 0C is used as an analog input pin of the A/D converter, set the P0CnIDI corresponding to the pin to which an analog voltage is applied to 1, to disable the port input function. Moreover, clear P0CBIOn (n = 0-3) to 0 to set the input port mode. The pin used as an analog input pin is selected by ADCCH0 and ADCCH1 (bits 1 and 0 of address 22H) on the register file. At reset, P0CBIO0-P0CBIO3, P0C0IDI-P0C3IDI, ADCCH0, and ADCCH1 are cleared to 0, setting the input port mode. Table 11-3. Selecting Port or A/D Converter Mode (n = 0 to 3) P0CnIDI RF:1BH 0 1 0 1 1 Port output Analog input of A/D Note 1 P0CBIOn RF:1CH 0 Function Write Input port BANK0 72H Read Pin status Contents of P0C latch Contents of P0C latch Contents of P0C latch Enabled. P0C latch Enabled. P0C latch Enabled. P0C latch Enabled. P0C latch Output port and analog input of A/D Note 2 Notes 1. 2. Normal setting when the P0C pins are used as the analog input pins of the A/D converter. The P0C pins function as output port pins. At this time, the analog input voltages change with the output from the port. To use the pins as analog input pins, be sure to clear P0CBIOn to 0. 32 PD17145(A1), 17147(A1), 17149(A1) 11.4 Port 0D (P0D0/SCK, P0D1/SO, P0D2/SI, P0D3/TM1OUT) Port 0D is a 4-bit I/O port with an output latch. It is mapped at address 73H of BANK0 of the data memory. The output format is N-ch open-drain output. This port can be set in the input or output mode in 1-bit units. The input or output mode is specified by P0DBIO0-P0DBIO3 (address 2BH) on the register file. When P0DBIOn = 0 (n = 0 to 3), the corresponding port pin, P0Dn, is set in the input mode. When an instruction that reads the data of the port register is executed at this time, the pin status is read. When P0DBIOn = 1, the P0Dn pin is set in the output mode, and the contents written to the output latch are output to the pin. When an instruction that reads the port status is executed with a port pin set in the output mode, the contents of the output latch, instead of the pin status, are read. A pull-up resistor can be connected on-chip to this port through software. Whether the pull-up resistor is connected or not is specified bitwise by using P0DBPU0-P0DBPU3 (address 0DH) on the register file. When P0DBPUn = 1, the P0Dn pin is pulled up. When P0DBPUn = 0, the pull-up resistor is not connected. At reset, P0DBIOn is cleared to "0", setting all the P0D pins in the input mode. The contents of the output latch are also cleared to "0" at this time. Note that the contents of the output latch are not changed even if the status of P0DBIOn is changed from "1" to "0". Port 0D is also used as serial interface input/output and timer 1 output pins. Whether the P0D 0 to P0D2 pins are used as port pins or serial interface I/O pins (SCK, SO, and SI) is specified by SIOEN (bit 0 of 0BH) on the register file. Whether the P0D3 pin is used as a port pin or timer 1 output (TM1OUT) pin is specified by TM1OSEL (bit 3 of 0BH) on the register file. If TM1OSEL = 1, "1" is output when timer 1 is reset, and the output is inverted each time the count value of timer 1 coincides with the contents of the modulo register. Table 11-4. Contents of Register File and Pin Function (n = 0 to 3) Value of Register File TM1OSEL RF: 0BH Bit 3 SIOEN RF: 0BH Bit 0 0 1 0 0 1 1 0 0 1 1 0 1 1 SCK SO SI Output port TM1OUT Input port SCK SO SI Input port Output port Output port P0DBIOn RF: 2BH Bit n 0 Input port P0D0/SCK P0D1/SO P0D2/SI P0D3/TM1OUT Pin Function 33 PD17145(A1), 17147(A1), 17149(A1) Table 11-5. Read Contents of Port Register (0.73H) Port Mode Input port Output port Internal clock selected as serial clock SCK External clock selected as serial clock SI SO TM1OUT Pin status Pin status Contents of output latch Contents of output latch Read Contents of Port Register (0.73H) Pin status Contents of output latch Contents of output latch 11.5 Port 0E (P0E0, P0E1, P0E2, P0E3) Port 0E is a 4-bit I/O port with an output latch. It is mapped at address 6EH of BANK0 of the data memory. The output format is N-ch open-drain output. This port can be set in the input or output mode in 4-bit units. The input or output mode is specified by P0EGIO (bit 2 of address 2CH) on the register file. When P0EGIO = 0, all the pins of port 0E are set in the input mode. When an instruction that reads the data of the port register is executed at this time, the pin status is read. When P0EGIO = 1, all the pins of port 0E are set in the output port, and the contents written to the output latch are output to the pins. When an instruction that reads the port status is executed with the port set in the output mode, the contents of the output latch, instead of the pin status, are read. A pull-up resistor can be connected on-chip to this port through software. Whether the pull-up resistor is connected is specified by P0EGPU (bit 2 at address 0CH) of the register file. All the four-bit pins are pulled up when P0EGPU = 1. When P0EGPU = 0, the pull-up resistor is not connected. P0EGIO is cleared to "0" at reset, and all the P0E pins are set in the input mode. The value of the output latch is also cleared to "0". Table 11-6. Writing and Reading Port Register (0.6EH) (n = 0 to 3) P0EGIO RF: 2CH, bit 2 0 1 Input/Output Mode of Pin Input Output Write Enabled Write to P0E latch BANK0 6EH Read P0E pin status P0E latch contents 11.6 Port 0F (P0F0/RLS, P0F1/VREF) Port 0F is a 2-bit input port and mapped at address 6FH of BANK0 of the data memory. A pull-up resistor can be connected on-chip bitwise to this port by mask option. If a read instruction that reads the port register is executed when both pins of port 0F are used as input port pins, the higher 2 bits of the register are fixed to 0, and the pin statuses are read to the lower 2 bits. Executing a write instruction is meaningless as the contents of the port register remain unchanged. The P0F0/RLS pin is also used to input a standby mode release signal. The P0F1/VREF pin inputs a reference voltage to the A/D converter when even one of the bits of P0CnIDI (RF: address 1BH, n = 0 to 3) is set to "1". If an instruction is executed to read the port register when the P0F1/VREF pin functions as the VREF pin, bit 1 of address 6FH is always cleared to 0. 34 PD17145(A1), 17147(A1), 17149(A1) 12. 8-BIT TIMERS/COUNTERS (TM0, TM1) The PD17149(A1) is provided with two 8-bit timers/counters: timer 0 (TM0) and timer 1 (TM1). By using the count-up signal of timer 0 as the count pulse to timer 1, the two 8-bit timers can be used as a 16-bit timer. Each timer is controlled through hardware manipulation by using the PUT or GET instruction or manipulation of the registers on the register file by using the PEEK or POKE instruction. 12.1 Configuration of 8-Bit Timers/Counters Figure 12-1 shows the configuration of the 8-bit timers/counters. An 8-bit timer/counter consists of an 8-bit count register, an 8-bit modulo register, a comparator that compares the value of the count register with that of the modulo register, and a selector that selects the count pulse. Cautions 1. 2. The modulo register is a write register. The count register is a read register. 35 PD17145(A1), 17147(A1), 17149(A1) Figure 12-1. Configuration of 8-Bit Timer/Counter Data buffer (DBF) Internal bus Interrupt control register (RF:0FH) INT Timer 0 mode register (RF:11H) TM0EN TM0RES TM0CK1 TM0CK0 Timer 0 modulo register (8) (TM0M) 2 Timer 0 comparator (8) Coincidence Timer 0 count-up signal (to timer 1) Latch Selector System clock/16 System clock/512 System clock/64 D CLK R Q INT Timer 0 count register (8) (TM0C) Clear IRQTM0 set signal Reset Internal reset IRQTM0 clear signal Data buffer (DBF) Internal bus Timer 1 mode register (RF:12H) TM1EN TM1RES TM1CK1 TM1CK0 Serial interface control register (RF:0BH) TM1OSEL Port control register of bit I/O (RF:2BH) P0DBIO3 Timer 1 modulo register (8) (TM1M) Coincidence 2 Timer 1 comparator (8) TM1OUT FF P0DB3 output latch P0D3/ TM1OUT Reset Latch System clock/128 System clock/8192 System clock/16 Timer 0 count up Selector D CLK R Q Timer 1 count register (8) (TM1C) Clear IRQTM1 set signal Reset Internal reset IRQTM1 clear signal 36 PD17145(A1), 17147(A1), 17149(A1) Figure 12-2. Timer 0 Mode Register RF : 11H Bit 3 TM0EN Bit 2 TM0RES Bit 1 TM0CK1 Bit 0 TM0CK0 Read/write Initial value at reset 0 0 R/W 0 0 Read = R, write = W TM0CK1 0 0 1 1 TM0CK0 0 1 0 1 Selects count pulse of timer 0 System clock/16 System clock/512 System clock/64 INT pin TM0RES 0 1 Resets timer 0 Does not affect timer 0 Resets timer 0 count register and IRQTM0 Remark TM0RES is automatically cleared to 0 after it has been set to 1. When it is read, "0" is always read. TM0EN 0 1 Timer 0 start command Stops counting of timer 0 Resumes counting of timer 0 Remark TM0EN can be used as a status flag that detects the count status of timer 0 (1 : counting in progress, 0 : counting stopped) 37 PD17145(A1), 17147(A1), 17149(A1) Figure 12-3. Timer 1 Mode Register RF : 12H Read/write Initial value at reset Bit 3 TM1EN Bit 2 TM1RES Bit 1 TM1CK1 Bit 0 TM1CK0 R/W 1 0 0 0 TM1CK1 0 0 1 1 TM1CK0 0 1 0 1 Selects count pulse of timer 1 System clock/128 System clock/8192 System clock/16 Count-up signal from timer 0 TM1RES 0 1 Resets timer 1 Does not affect timer 1 Resets timer 1 count register and IRQTM1 Remark TM1RES is automatically cleared to 0 after it has been set to 1. When it is read, "0" is always read. TM1EN 0 1 Timer 1 start command Stops counting of timer 1 Resumes counting of timer 1 Remark TM1EN can be used as a status flag that detects the count status of timer 1 (1 : counting in progress, 0 : counting stopped) 38 PD17145(A1), 17147(A1), 17149(A1) 13. BASIC INTERVAL TIMER (BTM) The PD17149(A1) is provided with a 7-bit basic interval timer. This timer has the following functions: (1) (2) (3) Generates reference time. Selects and counts wait time when standby mode is released. Watchdog timer function to detect program runaway. 13.1 Configuration of Basic Interval Timer Figure 13-1 shows the configuration of the basic interval timer. 39 PD17145(A1), 17147(A1), 17149(A1) Figure 13-1. Configuration of Basic Interval Timer Internal bus Watchdog timer mode register (RF:13H) BTMCK1 BTMCK0 WDTRES 0 0 WDTEN BTM mode register (RF:13H) BTMISEL BTMRES 2 fBTM 25 Reset fBTM fBTM 27 Selector (2) IRQBTM set signal Selector Basic interval timer (7-bit divider) (3) Reset signal System clock/16384 System clock/4096 System clock/512 System clock/16 Reset 1-bit divider R 1-shot pulse (1) S generator Q (4) Outputs "1" while counting 0 to 7 during counting from 0 to 255. Remark (1) to (4) in the figure correspond to the signals in the timing chart in Figure 13-4. 40 PD17145(A1), 17147(A1), 17149(A1) 13.2 Registers Controlling Basic Interval Timer The basic interval timer is controlled by the BTM mode register and watchdog timer mode register. Figures 13-2 and 13-3 show the configuration of each register. Figure 13-2. BTM Mode Register RF : 13H Bit 3 Bit 2 Bit 1 BTMCK1 Bit 0 BTMCK0 Read = R, Write = W 0 0 BTMISEL BTMRES Read/write Initial value at reset 0 0 R/W BTMCK1 0 BTMCK0 Selects count pulse to BTM System clock/16 0 (1 instruction execution time) System clock/16384 0 1 (1024 instruction execution time) System clock/4096 1 0 (256 instruction execution time) System clock/512 1 1 (32 instruction execution time) BTMRES 0 Resets BTM Does not affect basic interval timer (BTM) Resets binary counter of basic interval 1 timer (BTM) Remark BTMRES is automatically cleared to 0 after it has been set to 1. When it is read, "0" is always read. BTMISEL 0 Selects interval timer Sets interval timer to 1/128 of count pulse 1 Sets interval timer to 1/32 of count pulse 41 PD17145(A1), 17147(A1), 17149(A1) Figure 13-3. Watchdog Timer Mode Register RF : 03H Bit 3 WDTRES Read/write Initial value at reset 0 0 Bit 2 0 R/W 0 0 Bit 1 0 Bit 0 WDTEN Read = R, Write = W WDTEN 0 1 Enable watchdog timer Stops watchdog timer. Starts watchdog timer. Remark 1. WDTEN cannot be cleared to 0 by program. 2. WDTEN is automatically cleared to 0 after it has been set to 1. When it is read, "0" is always read. WDTRES 0 1 Resets watchdog timer Does not affect watchdog timer. Resets flip-flop that retains overflow carry of BTM used for watchdog timer. Remark WDTRES is automatically cleared to 0 after it has been set to 1. When it is read, "0" is always read. 42 PD17145(A1), 17147(A1), 17149(A1) 13.3 Watchdog Timer Function The basic interval timer can also be used as a watchdog timer that detects a program runaway. 13.3.1 Function of watchdog timer The watchdog timer is a counter that generates a reset signal at fixed time intervals. By inhibiting generation of this reset signal by program, the system can be reset (started from address 0000H) if the system becomes runaway due to external noise (if the watchdog timer is not reset within specific time). This function allows the program to escape from the runaway status because a reset signal is generated at fixed time intervals even when the program jumps to an unexpected routine and enters an indefinite loop due to external noise. 13.3.2 Operation of watchdog timer When WDTEN is set to 1, the 1-bit divider is enabled to operate, and the basic interval timer starts operating as an 8-bit watchdog timer. Once the watchdog timer has been started, it cannot be stopped until the device is reset and WDTEN is cleared to 0. Reset effected by the watchdog timer can be inhibited in the following two ways: (1) (2) Repeatedly set WDTRES in the program. Repeatedly set BTMRES in the program. In the case of (1), WDTRES must be set while the count value of the watchdog timer is 8 to 191 (before it reaches 192). Therefore, program so that "SET1 WDTRES" is executed at least once in a cycle shorter than that in which the watchdog timer counts 184. In the case of (2), BTMRES must be set before the basic interval timer (BTM) counts 128. Therefore, program so that "SET1 BTMRES" is executed at least once in a cycle shorter than that in which BTM counts 128. In this case, however, interrupts cannot be processed with BTM. Caution BTM is not reset even if WDTEN is set. Therefore, before setting WDTEN first, be sure to set BTMRES to reset BTM. Example SET1 BTMRES SET2 WDTEN, WDTRES ... ... 43 PD17145(A1), 17147(A1), 17149(A1) Figure 13-4. Timing Chart of Watchdog Timer (when WDTRES flag is used) 255 Count value of watchdog timer 128 192 128 192 255 192 128 64 128 192 255 8 0 0 8 0 8 0 WDTEN WDTRES acknowledge period WDTRES acknowledge period WDTRES acknowledge period WDTRES 1-shot pulse generator output (1) (4) fBTM/27 (2) ( IRQBTM set) fBTM/28 (3) Watchdog reset signal (active high) Reset signal is not generated 44 PD17145(A1), 17147(A1), 17149(A1) 14. A/D CONVERTER The PD17149(A1) is provided with an A/D converter with 4 analog input channels (P0C0/ADC0-P0C3/ADC3) and a resolution of 8 bits. This A/D converter is of the successive approximation type and operates in the following two modes: 1 2 Successive mode in which 8-bit A/D conversion is sequentially performed starting from the most significant bit Single mode in which an input analog voltage is compared with the set value of an 8-bit data register 14.1 Configuration of A/D Converter Figure 14-1 shows the configuration of the A/D converter. Figure 14-1. Block Diagram of A/D Converter Remark n = 0 to 3 Internal bus RF: 22H Read signal 0 0 ADCCH1 ADCCH0 RF: 20H RF: 21H ADCSOFT 0 ADCCMP ADCEND 0 0 0 ADCSTRT P0CnIDI P0CBIOn Selector Output latch Control circuit 8 Comparator 4 P0Cn/ADCn Selector 8-bit data register Note (ADCR) A/D end signal STOP instruction signal Tap decoder P0F1/VREF 8 3R/2 R 4 R R/2 D/A converter P0CnIDI P0F1 input data Note The 8-bit data register (ADCR) is cleared to 00H when the STOP instruction is executed. 45 PD17145(A1), 17147(A1), 17149(A1) 14.2 Function of A/D Converter (1) ADC0 to ADC3 pins These pins input analog voltages to the four channels of the A/D converter. The analog voltages are converted into digital signals. The A/D converter is provided with a sample and hold circuit, and an analog input voltage being converted into a digital signal is internally held. (2) VREF pin This pin inputs a reference voltage to the A/D converter. The signals input to ADC0 to ADC3 are converted into digital signals based on the voltage applied across VREF and GND. The A/D converter of the PD17149(A1) has a function to automatically stop the current flowing into the VREF pin when the A/D converter does not operate. A current flows into the VREF pin in the following cases: 1 2 In successive mode (ADCSOFT = 0) Since the ADCSTRT flag has been set to 1 until the ADCEND flag is set to 1. In single mode (ADCSOFT = 1) Since the ADCSTRT flag has been set to 1 or a value has been written to the 8-bit data register until the result of comparison by the comparator is written to the ADCCMP flag. Remarks 1. If the HALT instruction is executed during A/D conversion, the A/D converter operates, in the successive mode, until the ADCEND flag is set, or in the single mode, until the result of conversion is stored to the ADCCMP flag. Therefore, a current flows to the VREF pin during this period. 2. A/D conversion in progress is stopped if the STOP instruction is executed. In this case, the A/D converter is initialized, and the current flowing to the VREF pin is cut (the A/D converter does not operate even if the STOP mode has been released). (3) 8-bit data register (ADCR) This is an 8-bit register that stores the result of A/D conversion of successive approximation type in the successive mode. The contents of this register are read by using the GET instruction. In the single mode, the contents of the 8-bit data register are converted into an analog voltage by an internal D/A converter and is compared by the comparator with an analog signal input from the ADCn pin. A value can be written to this register by using the PUT instruction. (4) Comparator The comparator compares the analog input voltage with the voltage output by the D/A converter. If the analog input voltage is high, it outputs "1"; if the voltage is low, the comparator outputs "0". The result of comparison is stored to the 8-bit data register (ADCR) in the successive mode, and to the ADCCMP flag in the single mode. 46 PD17145(A1), 17147(A1), 17149(A1) 14.3 Operation of A/D Converter The operation of the A/D converter can be executed in two modes, depending on the setting of the ADCSOFT flag: successive and single modes. ADCSOFT 0 1 Operation Mode of A/D Converter Successive mode (A/D conversion) Single mode (compare operation) Figure 14-2. Relationships between Analog Input Voltage and Digital Conversion Result Ideal conversion result FFH FEH FDH Digital conversion result N 03H 02H 01H 00H 0 (x VDD) 1 256 2 256 N 256 Analog input voltage (V) 254 256 255 256 256 256 47 PD17145(A1), 17147(A1), 17149(A1) (1) Timing in successive mode (A/D conversion) Figure 14-3. Timing in Successive Mode (A/D Conversion) Number of executed instructions (instruction cycle) POKE 1 2 3 4 5 6 7 8 9 24 GET Sampling Sampling Sampling ADCSTRT executed ADCR read ADCSTRT ADCEND 8-bit data register Previous data Initial value:80H Highest 1 bit determined Highest 2 bits determined All 8 bits determined Caution Sampling is performed eight times while A/D conversion is executed once. If the analog input voltage changes heavily during A/D conversion, A/D conversion cannot be performed accurately. To obtain an accurate conversion result, it is necessary to minimize the changes in the analog input voltage during A/D conversion. Remark One sampling time = 14/fx (1.75 s, at 8 MHz) Sampling repeat cycle = 48/fx (6 s, at 8 MHz) Sampling capacitor capacitance = 100 pF (MAX.) 48 PD17145(A1), 17147(A1), 17149(A1) (2) Timing in single mode (compare operation) Figure 14-4. Timing in Single Mode (Compare Operation) Number of executed instructions (instruction cycle) POKE 1 2 PEEK PUT 1 2 PEEK Sampling ADCSTRT executed ADCCMP read Sampling ADCCMP read ADCSTRT ADCEND ADCCMP Previous data Comparison result Comparison result After 1 has been written to ADCSTRT in the single mode (execution of the POKE instruction), a value is stored to ADCCMP three instructions after, and the result of comparison can be read by the PEEK instruction. Even if data is set to ADCR (execution of the PUT instruction), comparison is started in the same manner as ADCSTRT, and the result of comparison can be read three instructions after. The ADCCMP flag is cleared to 0 when reset is executed or when an instruction that writes data to ADCR is executed. Caution Be sure to set ADCSOFT to 1 before setting a value to ADCR. When ADCSOFT = 0, no value can be set to ADCR (the PUT ADCR, DBF instruction is invalidated). Remark Sampling time = 14/fx (1.75 s, at 8 MHz) Sampling capacitor capacitance = 100 pF (MAX.) 49 PD17145(A1), 17147(A1), 17149(A1) 15. SERIAL INTERFACE (SIO) The serial interface of the PD17149(A1) consists of an 8-bit shift register (SIOSFR), a serial mode register, and a serial clock counter, and is used to input/output serial data. 15.1 Function of Serial Interface The serial interface can transmit or receive 8-bit data in synchronization with the clock by using three wires: serial clock input (SCK), serial data output (SO), and serial data input (SI) pins. This serial interface can connect various peripheral I/O devices in a mode compatible with the method employed for the PD7500 series and 75X series. (1) Serial clock Four types of serial clocks, three internal and one external, can be selected. If an internal clock is selected as the serial clock, the selected clock is automatically output to the P0D0/SCK pin. Table 15-1. Serial Clocks SIOCK1 0 0 1 1 SIOCK0 0 1 0 1 Selected Serial Clock External clock from SCK pin System clock/16 System clock/128 System clock/1024 (2) Transfer operation Each pin of port 0D (P0D0/SCK, P0D1/SO, P0D2/SI) functions as a serial interface pin when SIOEN is set to 1. If SIOTS is set to 1 at this time, the serial interface starts its operation in synchronization with the falling edge of the external or internal clock. If SIOTS is set, IRQSIO is automatically cleared. Data is transferred starting from the most significant bit of the shift register in synchronization with the rising edge of the serial clock, and the information on the SI pin is stored to the shift register, starting from the least significant bit, in synchronization with the rising edge of the serial clock. When 8-bit data has been completely transferred, SIOTS is automatically cleared, and IRQSIO is set. Remark When serial transfer is executed, transfer is started only from the most significant bit of the contents of the shift register. In other words, transfer cannot be started from the least significant bit. The status of the SI pin is always loaded to the shift register in synchronization with the rising edge of the serial clock. 50 PD17145(A1), 17147(A1), 17149(A1) Figure 15-1. Block Diagram of Serial Interface P0D2/SI LSB MSB Shift register (SIOSFR) SIOTS Serial start Output latch SIOHIZ SIOCK1 SIOCK0 IRQSIO clear signal P0D1/SO Selector P0D1 output latch One shot P0D0/SCK Clock Serial clock counter Carry Clear IRQSIO set signal S Selector Q R P0D0 output latch Selector fx/1024 fx/128 SIOEN P0DBIO0 P0DBIO1 Caution The output latch of the shift register is independent of the output latch of P0D1. Therefore, even if an output instruction is executed to P0D1, the status of the output latch of the shift register is not affected. The output latch of the shift register is cleared to "0" by RESET input. After that, it holds the status of the LSB of the previously transferred data. fx/16 51 PD17145(A1), 17147(A1), 17149(A1) 15.2 Operation Mode of 3-Wire Serial Interface The serial interface can operate in the following two modes. When the serial interface function is selected, the P0D2/SI pin always inputs data in synchronization with the serial clock. * 8-bit transmission/reception mode (simultaneous transmission/reception) * 8-bit reception mode (SO pin: high-impedance state) Table 15-2. Operation Modes of Serial Interface SIOEN 1 1 0 x : Don't care SIOHIZ 0 1 x P0D0/SI Pin SI SI P0D0 (I/O) P0D1/SO Pin SO P0D1 (input) P0D1 (I/O) Operation Mode of Serial Interface 8-bit transmission/reception mode 8-bit reception mode General-purpose port mode (1) 8-bit transmission/reception mode (simultaneous transmission/reception) Input or output of serial data is controlled by the serial clock. The MSB of the shift register is output to the SO line at the falling edge of the serial clock (SCK pin signal). The contents of the shift register are shifted 1 bit at the rising edge of the serial clock. At the same time, the data on the SI line is loaded to the LSB of the shift register. The serial clock counter (3-bit counter) sets an interrupt request flag (IRQSIO <- 1) each time it has counted eight serial clocks. Figure 15-2. Timing in 8-Bit Transmission/Reception Mode (Simultaneous Transmission/Reception) SCK pin 1 2 3 4 5 6 7 8 SI pin DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 SO pin DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 IRQSIO Starts transfer in synchronization with falling of SCK pin Executes instruction that writes "1" to SIOTS (transfer start command) End of transfer Remark DI: serial data input DO: serial data output 52 PD17145(A1), 17147(A1), 17149(A1) (2) 8-bit reception mode (SO pin: high-impedance state) The P0D1/SO pin goes into a high-impedance state when SIOHIZ = 1. If supply of the serial clock is started at this time by writing "1" to SIOTS, the serial interface only receives data. Because the P0D1/SO pin goes into a high-impedance state, it can be used as an input port pin (P0D1). Figure 15-3. Timing in 8-Bit Reception Mode SCK pin 1 2 3 4 5 6 7 8 SI pin DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 SO pin Hi - Z IRQSIO Starts transfer in synchronization with falling of SCK pin Executes instruction that writes "1" to SIOTS (transfer start command) End of transfer Remark DI: serial data input (3) Operation stop mode When the value of SIOTS (RF: address 02H, bit 3) is 0, the serial interface is set in the operation stop mode. In this mode, serial transfer is not executed. Because the shift register does not perform the shift operation in this mode, it can be used as an ordinary 8-bit register. 53 PD17145(A1), 17147(A1), 17149(A1) 16. INTERRUPT FUNCTION The PD17149(A1) has five interrupt causes, of which four are internal and one is external, enabling various applications. The interrupt control circuit of the PD17149(A1) has the following features and can perform interrupt processing at extremely high speeds: (a) Acknowledging an interrupt can be controlled by interrupt mask enable flag (INTE) and interrupt enable flag (IPxxx). (b) Interrupt request flags (IRQxxx) can be tested and cleared (occurrence of an interrupt can be checked by software). (c) Multiple interrupts of up to 3 levels can be processed. (d) The standby mode (STOP or HALT) can be released by an interrupt request (releasing condition can be selected by the interrupt enable flag). Caution Only the BCD, CMP, CY, Z, and IXE flags are automatically saved to the stack by hardware when interrupt processing is performed. Up to three levels of multiple interrupts can be processed. If the peripheral hardware (timers, A/D converter, etc.) is accessed during interrupt processing, the contents of DBF and WR are not saved by the hardware. It is therefore recommended that DBF and WR be saved to the RAM by software at the beginning of interrupt processing, and that their contents be restored immediately before the interrupt processing. 16.1 Types of Interrupt Causes and Vector Addresses All the interrupts of the PD17149 (A1) are vectored interrupts, and therefore, program execution branches to a vector address corresponding to the interrupt cause when an interrupt has been acknowledged. Table 161 shows the types of interrupt causes and vector addresses. If two or more interrupts occur at the same time, or if two or more pending interrupts are enabled all at once, processing is performed according to the priority shown in Table 16-1. Table 16-1. Types of Interrupt Causes Interrupt Cause INT pin (RF: 0FH, bit 0) Priority 1 Vector Address 0005H IRQ Flag IRQ RF: 3FH, bit 0 IRQTM0 RF: 3EH, bit 0 IRQTM1 RF: 3DH, bit 0 IRQBTM RF: 3CH, bit 0 IRQSIO RF: 3BH, bit 0 IP Flag IP RF: 2FH, bit 0 IPTM0 RF: 2FH, bit 1 IPTM1 RF: 2FH, bit 2 IPBTM RF: 2FH, bit 3 IPSIO RF: 2EH, bit 0 IEG Flag IEGMD0, 1 RF:1FH Internal /External External Remark Rising, falling, or both rising and falling edges selectable Timer 0 2 0004H Internal -- Timer 1 3 0003H Internal -- Basic interval timer 4 0002H -- Internal Serial interface 5 0001H Internal -- 54 PD17145(A1), 17147(A1), 17149(A1) 16.2 Hardware of Interrupt Control Circuit This section describes each flag of the interrupt control circuit. (1) Interrupt request flags and interrupt enable flags An interrupt request flag (IRQxxx) is set to 1 when an interrupt request is generated, and automatically cleared to 0 when interrupt processing is executed. An interrupt enable flag (IPxxx) is provided for each interrupt request flag. The corresponding interrupt is enabled when this flag is "1", and disabled when the flag is "0". (2) EI/DI instruction Whether an interrupt that has been acknowledged is executed is specified by the EI or DI instruction. When the EI instruction is executed, an interrupt enable flag (INTE) that enables acknowledging an interrupt is set to 1. The INTE flag is not registered on the register file. Therefore, the status of this flag cannot be checked by an instruction. The DI instruction clears the INTE flag to "0", disabling all the interrupts. The INTE flag is also cleared to 0 at reset, and therefore all the interrupts are disabled. Table 16-2. Interrupt Request Flags and Interrupt Enable Flags Interrupt Request Flag IRQ Interrupt Request Flag Setting Signal Sets when edge of INT pin input signal is detected. Edge to be detected is selected by IEGMD0 and IEGMD1 flags. Set by coincidence signal from timer 0. Set by coincidence signal from timer 1. Set by overflow from basic interval timer (reference time interval signal). Set when serial interface completes serial data transfer. Interrupt Enable Flag IP IRQTM0 IRQTM1 IRQBTM IPTM0 IPTM1 IPBTM IRQSIO IPSIO 55 PD17145(A1), 17147(A1), 17149(A1) 17. STANDBY FUNCTION 17.1 Outline of Standby Function The current dissipation of the PD17149(A1) can be reduced by using the standby function. This function can be effected in two modes: STOP and HALT. The STOP mode stops the system clock. In this mode, the current dissipation by the CPU is minimized with only leakage current flowing. The CPU therefore does not operate, but the contents of the data memory are retained. In the HALT mode, oscillation of the clock continues. However, supply of the clock to the CPU is stopped. Therefore, the CPU stops operating. This mode cannot reduce the current dissipation as much as the STOP mode. However, because the system clock continues oscillating, the operation can be started immediately after the HALT mode has been released. In both the STOP and HALT modes, the statuses of the data memory, registers, and the output latches of the output ports immediately before the standby mode is set are retained (except STOP 0000B). Therefore, set the port status so that the current dissipation of the entire system is reduced before the standby mode is set. 56 PD17145(A1), 17147(A1), 17149(A1) Table 17-1. Status in Standby Mode STOP Mode Setting instruction Clock oscillation circuit CPU RAM Port TM0 Operating status STOP instruction HALT Mode HALT instruction Stops oscillation * Stops operation * Retains previous status * Retains previous status Note * Can operate only when INT input is selected as count clock * Stops when system clock is selected (count value is retained) * Stops operation (count value is reset to "0") (count up is disabled) Continues oscillation * Operable TM1 * Operable BTM SIO * Stops operation (count value is retained) * Can operate only when external clock is selected as serial clock Note * Stops operation Note (ADCR <- 00H) * Can operate * Operable * Operable A/D INT * Operable * Operable Note As soon as the STOP 0000B instruction is executed, the pins of these peripherals are set in the input port mode, even when the control signal functions of the pins are used. Cautions 1. 2. Be sure to execute the NOP instruction immediately before the STOP and HALT instructions. If both the interrupt request flag and interrupt enable flag corresponding to an interrupt are set, and if the interrupt is specified to release the standby mode, the standby mode is not set even if the STOP or HALT instruction is executed. 57 PD17145(A1), 17147(A1), 17149(A1) 17.2 HALT Mode 17.2.1 Setting HALT mode The HALT mode is set when the HALT instruction is executed. The operand of the HALT instruction, b3b2b1b0, specifies the condition under which the HALT mode is released. Table 17-2. HALT Mode Releasing Condition Format: HALT b3b2b1b0B Bit b3 b2 b1 b0 HALT mode releasing condition Note 1 Enables releasing HALT mode by IRQxxx when 1 Notes 2, 4 Fixed to "0" Enables forced release of HALT mode by IRQTM1 when 1 Notes 3, 4 Enables releasing HALT mode by RLS input when 1Note 4 Notes 1. 2. 3. 4. Only reset (RESET input or POC) is valid when HALT 0000B is specified. IPxxx must be set to 1. The HALT mode is released regardless of the status of IPTM1. Even if the HALT instruction is executed with IRQxxx = 1 or RLS input being low, the HALT instruction is ignored (treated as an NOP instruction), and the HALT mode is not set. 17.2.2 Start address after HALT mode is released The start address from which the program execution is started after the HALT mode has been released differs depending on the interrupt enable condition and the condition under which the HALT mode has been released. Table 17-3. Start Address after HALT Mode Is Released Releasing Condition Reset RLS Note 1 Start Address after Release Address 0 Address next to that of HALT instruction Address next to that of HALT instruction in DI status IRQxxx Note 2 Interrupt vector in EI status (if two or more IRQxxx flags are set, interrupt vector with higher priority) Notes 1. 2. RESET input and POC are valid as reset. IPxxx must be set to 1 except when the HALT mode is forcibly released by IRQTM1. 58 PD17145(A1), 17147(A1), 17149(A1) Figure 17-1. Releasing HALT Mode (a) By RESET input HALT instruction executed RESET TM1 counts up Operation mode HALT mode System reset status WAIT a Operation mode (starts from address 0) WAIT a : Wait time until TM1 counts 256 clocks divided by 128 256x128/fX (approx. 4 ms at fX =8 MHz) (b) By RLS input HALT instruction executed RLS Operation mode HALT mode Operation mode (c) By IRQxxx (in DI status) HALT instruction executed IRQxxx Operation mode HALT mode Operation mode (d) By IRQxxx (in EI status) Interrupt processing acknowledged HALT instruction executed IRQxxx Operation mode HALT mode Operation mode 59 PD17145(A1), 17147(A1), 17149(A1) 17.3 STOP Mode 17.3.1 Setting STOP mode The STOP mode is set when the STOP instruction is executed. The operand of the STOP instruction, b3b2b1b0, specifies the condition under which the STOP mode is released. Table 17-4. STOP Mode Releasing Condition Format: STOP b3b2b1b0B Bit b3 b2 b1 b0 STOP mode releasing condition Note 1 Enables releasing HALT mode by IRQxxx when 1 Notes 2, 4 Fixed to "0" Fixed to "0" Enables releasing STOP mode by RLS input when 1 Notes 3, 4 Notes 1. Only reset (RESET input or POC) is valid when STOP 0000B is specified. When STOP 0000B is executed, the internal circuitry of the microcontroller is initialized to the status immediately after reset. 2. 3. 4. IPxxx must be set to 1. The STOP mode cannot be released by IRQTM1. b0 alone cannot be set to 1 (STOP 0001B is prohibited). Before setting b0 to 1, be sure to set b3 to 1. Even if the STOP instruction is executed with IRQxxx = 1 or the RLS input being low, the STOP instruction is ignored (treated as an NOP instruction), and the STOP mode is not set. 17.3.2 Start address after STOP mode is released The start address from which the program execution is started after the STOP mode has been released differs depending on the condition under which the STOP mode has been released, and interrupt enable condition. Table 17-5. Start Address after STOP Mode Is Released Releasing Condition Reset RLS Note 1 Start Address after Release Address 0 Address next to that of STOP instruction Address next to that of HALT instruction in DI status IRQxxx Note 2 Interrupt vector in EI status (if two or more IRQxxx flags are set, interrupt vector with higher priority) Notes 1. 2. RESET input and POC are valid as reset. IPxxx must be set to 1. The STOP mode cannot be released by IRQTM1. 60 PD17145(A1), 17147(A1), 17149(A1) Figure 17-2. Releasing STOP Mode (a) By RESET input STOP instruction executed RESET TM1 counts up Operation mode STOP mode System reset status WAIT b Operation mode (starts from address 0) WAIT b : Wait time until TM1 counts 256 clocks divided by 128 256 x 128/fX + (apporox. 4 ms + at fX = 8 MHz) : Oscillation growth time (differs depending on the oscillator) (b) By RLS input STOP instruction executed RLS TM1 counts up Operation mode STOP mode WAIT c Operation mode WAIT c : Wait time until TM1 counts clocks divided by m n times n x m/fX + (n and m are values immediately before STOP mode is set) : Oscillation growth time (differs depending on the oscillator) (c) By IRQxxx (in DI status) STOP instruction executed IRQxxx TM1 counts up Operation mode STOP mode WAIT c Operation mode WAIT c : Wait time until TM1 counts clocks divided by m n times n x m/fX + (n and m are values immediately before STOP mode is set) : Oscillation growth time (differs depending on the oscillator) 61 PD17145(A1), 17147(A1), 17149(A1) (d) By IRQxxx (in EI status) STOP instruction executed IRQxxx TM1 counts up, interrupt processing acknowledged Operation mode STOP mode WAIT c Operation mode WAIT c : Wait time until TM1 counts clocks divided by m n times n x m/f X + (n and m are values immediately before STOP mode is set) : Oscillation growth time (differs depending on the oscillator) 62 PD17145(A1), 17147(A1), 17149(A1) 18. RESET The PD17149 (A1) can be reset not only by the RESET input, but also by the internal POC circuit that detects a supply voltage drop, watchdog timer function that resets the microcontroller if program runaway occurs, and overflow or underflow of the address stack. Note, however, that the internal POC circuit is a mask option. 18.1 Reset Function The reset function initializes the device operation. How the device is initialized differs depending on the type of reset. Table 18-1. Hardware Status at Reset * RESET Input during Operation * Reset by Internal POC Circuit * RESET Input in Standby Mode * Reset by Internal POC Circuit in Standby Mode 0000H Input 0 * Overflow of Watchdog Timer * Overflow and Underflow of Stack Type of Reset Hardware Program counter Input/output Port Contents of output latch General-purpose data memory (except DBF) DBF System register (except WR) WR 0000H Input 0 0000H Input Undefined Undefined Retains contents Undefined General-purpose data memory Undefined 0 Undefined Undefined 0 Retains contents Undefined 0 Undefined SP = 5H, INT = status at that time. Others retain contents. Control register SP = 5H, IRQTM1 = 1, TM1EN = 1, IRQBTM = 1, INT = status at that time. Others are 0. Refer to 8. REGISTER FILE (RF). Count register Modulo register 00H FFH 00H FFH Timer 0 and timer 1 Timer 0: 00H, timer 1: undefined FFH Undefined. However, 40H if watchdog timer overflows. Undefined Undefined 00H Binary counter of basic interval timer Undefined Undefined Serial interface Shift register (SIOSFR) Output latch Undefined 0 00H Retains contents 0 00H Data register of A/D converter (ADCR) 63 PD17145(A1), 17147(A1), 17149(A1) Figure 18-1. Configuration of Reset Block VDD Mask option POC circuit (mask option) Internal reset signal RESET 18.2 Reset Operation Figure 18-2 shows the operation when the system is reset by using the RESET pin. When the RESET pin is made high, oscillation of the system clock is started, oscillation stabilization wait time specified by timer 1 elapses, and program execution is started from address 0000H. These operations are also performed if the system is reset by the POC circuit. If the system is reset by using an overflow of the watchdog timer or an overflow or underflow of the stack, the oscillation stabilization wait time (WAIT a) does not elapse, and program execution is started from address 0000H after the internal circuitry has been initialized. Figure 18-2. Reset Operation RESET TM1EN TM1RES Operation mode Reset WAIT a Note Operation mode Note Oscillation stabilization wait time. An operation mode is set when system clock is counted 128 x 256 times by timer 1 (time required to executed 2048 instructions: approx. 4 ms at 8 MHz). 64 PD17145(A1), 17147(A1), 17149(A1) 19. POC CIRCUIT (MASK OPTION) The POC circuit monitors the supply voltage. When the supply voltage is turned ON/OFF, it automatically resets the internal circuitry of the microcontroller. This circuit can be used in an application circuit with a clock frequency of 400 kHz to 4 MHz. The PD17149 (A1) can be provided with the POC circuit by mask option. Caution The POC circuit is not provided to the PROM model (PD17P149). 19.1 Function of POC Circuit The POC circuit has the following functions: * Generates internal reset signal when VDD VPOC * Clears internal reset signal when VDD > VPOC (where, VDD: supply voltage, VPOC: POC detection voltage) Figure 19-1. Operation of POC Circuit VDD 5.5 V 4.5 V VPOC 2.7 V Note 3 0V Note 3 t Internal reset signal Reset Note 1 Operation modeNote 4 Reset Note 2 Operation guaranteed range 65 PD17145(A1), 17147(A1), 17149(A1) Notes 1. Actually, oscillation stabilization wait time specified by timer 1 elapses before the operation mode is set. This time is equal to that required for executing about 2048 instructions (approx. 8 ms at 4 MHz). 2. To reset the microcontroller again when the supply voltage drops, the status in which the voltage drops below VPOC must be maintained at least for the duration of the reset detection pulse width tSAMP. Therefore, reset is actually effected with a delay time of up to tSAMP. 3. The operation is not guaranteed if the supply voltage drops below the rated minimum value (2.7 V). However, the POC circuit is designed to generate the internal reset signal so long as it is possible, regardless of oscillation. Therefore, the internal circuitry is reset when the voltage supplied to it has reached the level at which the circuitry can operate. 4. If the supply voltage abruptly increases (3 V/ms MIN.), the POC circuit may generate the internal reset signal, even in an operation mode, to prevent program runaway. Remark For the values of VPOC and tSAMP, refer to 22. ELECTRICAL SPECIFICATIONS. 19.2 Conditions to Use POC Circuit The POC circuit can be used when the application circuit satisfies the following conditions: * The application circuit does not require a high reliability. * The operating voltage must range from 4.5 to 5.5 V. * The clock frequency must range from 400 kHz to 4 MHz. * The supply voltage must satisfy the ratings of the POC circuit. Cautions 1. 2. If the application circuit requires an extremely high reliability, design the circuit so that the RESET signal is input from an external source. The current dissipation in the standby mode slightly increases if the POC circuit is used. Remark The guaranteed operating voltage range of the POC circuit is VDD = 2.7 to 5.5 V. 66 PD17145(A1), 17147(A1), 17149(A1) 20. INSTRUCTION SET 20.1 Outline of Instruction Set b15 b14-b11 BIN 0000 0001 0010 0011 0100 0101 0110 HEX 0 1 2 3 4 5 6 ADD SUB ADDC SUBC AND XOR OR INC INC MOVT BR CALL RET RETSK EI DI 0111 7 RETI PUSH POP GET PUT PEEK POKE RORC STOP HALT NOP 1000 1001 1010 1011 1100 1101 1110 1111 8 9 A B C D E F LD SKE MOV SKNE BR BR r, m m, #n4 @r, m m, #n4 addr (page 0) addr (page 1) ST SKGE MOV SKLT CALL MOV SKT SKF m, r m, #n4 m, @r m, #n4 addr m, #n4 m, #n m, #n AR AR DBF, p p, DBF WR, rf rf, WR r s h r, m r, m r, m r, m r, m r, m r, m AR IX DBF, @AR @AR @AR ADD SUB ADDC SUBC AND XOR OR m, #n4 m, #n4 m, #n4 m, #n4 m, #n4 m, #n4 m, #n4 0 1 67 PD17145(A1), 17147(A1), 17149(A1) 20.2 Legend AR ASR addr BANK CMP CY DBF h INTEF INTR INTSK IX MP MPE m mR mC n n4 PAGE PC p pH pL r rf rfR rfC SP s WR (x) : address register : address stack register indicated by stack pointer : program memory address (lower 11 bits) : bank register : compare flag : carry flag : data buffer : halt release condition : interrupt enable flag : register automatically saved to the stack when interrupt processing is performed : interrupt stack register : index register : data memory row address pointer : memory pointer enable flag : data memory address indicated by mR, mC : data memory row address (high) : data memory column address (low) : bit position (4 bits) : immediate data (4 bits) : page (bit 11 of program counter) : program counter : peripheral address : peripheral address (higher 3 bits) : peripheral address (lower 4 bits) : general register column address : register file address : register file row address (higher 3 bits) : register file column address (lower 4 bits) : stack pointer : stop release condition : window register : contents addressed by x 68 PD17145(A1), 17147(A1), 17149(A1) 20.3 Instruction Set Instruc- Mnemonic tion ADD m, #n4 Addition r, m ADDC m, #n4 AR INC IX Subtraction r, m SUB m, #n4 r, m SUBC m, #n4 r, m Logical operation OR m, #n4 r, m AND m, #n4 r, m XOR m, #n4 Judgment Operand r, m (r) (r) + (m) (m) (m) + n4 (r) (r) + (m) + CY (m) (m) + n4 + CY AR AR + 1 IX IX + 1 (r) (r) - (m) (m) (m) - n4 (r) (r) - (m) - CY (m) (m) - n4 - CY (r) (r) (m) (m) (m) n4 (r) (r) (m) (m) (m) n4 (r) (r) (m) (m) (m) n4 Operation Instruction code op code 00000 10000 00010 10010 00111 00111 00001 10001 00011 10011 00110 10110 00100 10100 00101 10101 11110 11111 01001 01011 11001 11011 00111 mR mR mR mR Operand mC mC mC mC r n4 r n4 000 1001 0000 000 1000 0000 mR mR mR mR mR mR mR mR mR mR mR mR mR mR mR mR mC mC mC mC mC mC mC mC mC mC mC mC mC mC mC mC r n4 r n4 r n4 r n4 r n4 n n n4 n4 n4 n4 r r r r SKT SKF SKE SKNE SKGE SKLT RORC LD ST m, #n m, #n m, #n4 m, #n4 m, #n4 m, #n4 r r, m m, r @r, m CMP 0, if (m) n = n, then skip CMP 0, if (m) n = 0, then skip (m) - n4, skip if zero (m) - n4, skip if not zero (m) - n4, skip if not borrow (m) - n4, skip if borrow CY (r) b3 (r) b2 (r) b1 (r) b0 Rotation Comparison 000 0111 mR mR mR mC mC mC (r) (m) (m) (r) if MPE = 1: (MP, (r)) (m) if MPE = 0: (BANK, mR, (r)) (m) if MPE = 1: (m) (MP, (r)) if MPE = 0: (m) (BANK, mR, (r)) (m) n4 SP SP -1, ASR PC, PC AR, DBF (PC), PC ASR, SP SP +1 SP SP -1, ASR AR AR ASR, SP SP +1 WR (rf) (rf) WR DBF (p) (p) DBF 01000 11000 01010 MOV m, @r Transfer m, #n4 MOVT PUSH POP PEEK POKE GET PUT DVF, @AR AR AR WR, rf rf, WR DBF, p p, DBF 11010 11101 00111 00111 00111 00111 00111 00111 00111 mR mR mC mC r n4 000 0001 0000 000 1101 0000 000 1100 0000 rfR rfR pH pH 0011 0010 1011 1010 rfC rfC pL pL 69 PD17145(A1), 17147(A1), 17149(A1) Instruc- Mnemonic tion Branch BR @AR addr Subroutine CALL @AR RET RETSK RETI Interrupt Operand addr Note PC AR Operation Instruction code op code Note 00111 11100 Operand addr 000 0100 0000 addr SP SP - 1, ASR PC, PC addr SP SP - 1, ASR PC, PC AR PC ASR, SP SP + 1 PC ASR, SP SP + 1 and skip PC ASR, INTR INTSK, SP SP + 1 INTEF 1 INTEF 0 s h STOP HALT No operation 00111 00111 00111 00111 00111 00111 00111 00111 00111 000 0101 0000 000 1110 0000 001 1110 0000 100 1110 0000 000 1111 0000 001 1111 0000 010 1111 011 1111 s h EI DI STOP HALT NOP Others 100 1111 0000 Note The operation and op code of "BR addr" of the PD17145(A1), 17147(A1), and PD17149(A1) are as follows: (a) PD17145(A1), 17147(A1) Mnemonic BR Operand addr Operation PC addr, PAGE 0 op code 01100 (b) PD17149(A1) Mnemonic BR Operand addr Operation PC addr, PAGE 0 PC addr, PAGE 1 op code 01100 01101 70 PD17145(A1), 17147(A1), 17149(A1) 20.4 Assembler (AS17K) Embedded Macro Instruction Legend flag n: < >: FLG type symbol Can be omitted Mnemonic SKTn SKFn Embedded macro SETn CLRn NOTn Operand flag 1, ...flag n flag 1, ...flag n flag 1, ...flag n flag 1, ...flag n flag 1, ...flag n 1n4 n=0 71 PD17145(A1), 17147(A1), 17149(A1) 21. ASSEMBLER RESERVED WORDS 21.1 Mask Option Directive The PD17149 (A1) has the following mask options: * Internal pull-up resistor of RESET pin * Internal pull-up resistor of P0F1 and P0F0 pins * Internal pull-up resistor of INT pin * Internal POC circuit When developing a program, it is necessary to specify all the above mask options in the source program by using a mask option definition directive (pseudo instruction). 21.1.1 Specifying mask option The mask option is described in the assembler source program by using the following directives: * OPTION directive, ENDOP directive * Mask option definition directive (1) OPTION and ENDOP directives These directives specify the range in which the mask option is specified (mask option definition block). Specify the mask option by describing a mask option definition directive in the area sandwiched between the OPTION and ENDOP directives. Format Symbol field [label:] Mnemonic field OPTION ENDOP ... Operand field Comment field [;comment] 72 PD17145(A1), 17147(A1), 17149(A1) (2) Mask option definition directives Table 21-1. Mask Option Definition Directives Option Internal pull-up resistor of RESET pin Internal pull-up resistor of P0F1 and P0F0 pins Internal pull-up resistor of INT pin Internal POC circuit OPTPOC Note Definition Directive and Format OPTRES Operand OPEN PULLUP OPEN PULLUP OPEN PULLUP NOUSE USE Defined Contents None Defined None Defined None Defined Not used Used Note (3) Example of mask option description ; Example of describing mask option of the PD17149 (A1) MASK_OPTION: OPTION OPTRES PULLUP ; start of mask option definition block ; connects internal pull-up resistor to RESET pin nally pulled up) OPTINT PULLUP OPTPOC NOUSE ENDOP ; connects internal pull-up resistor to INT pin ; internal POC circuit is not used ; End of mask option definition block OPTP0F PULLUP, OPEN ; connects internal pull-up resistor to P0F1, and leaves P0F0 open (exter- 73 PD17145(A1), 17147(A1), 17149(A1) 21.2 Reserved Symbols The following tables show the reserved symbols defined by the device file (AS17149) of the PD17149(A1): System register (SYSREG) Symbol Name AR3 AR2 AR1 AR0 WR BANK IXH MPH MPE IXM MPL IXL RPH RPL PSW BCD CMP CY Z IXE Attribute MEM MEM MEM MEM MEM MEM MEM MEM FLG MEM MEM MEM MEM MEM MEM FLG FLG FLG FLG FLG Value 0.74H 0.75H 0.76H 0.77H 0.78H 0.79H 0.7AH 0.7AH 0.7AH.3 0.7BH 0.7BH 0.7CH 0.7DH 0.7EH 0.7FH 0.7EH.0 0.7FH.3 0.7FH.2 0.7FH.1 0.7FH.0 Read/Write R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Description Bits b15-b12 of address register Bits b11-b8 of address register Bits b7-b4 of address register Bits b3-b0 of address register Window register Bank register Index register, high Data memory row address pointer, high Memory pointer enable flag Index register, middle Data memory row address pointer, low Index register, low General register pointer, high General register pointer, low Program status word BCD flag Compare flag Carry flag Zero flag Index enable flag 74 PD17145(A1), 17147(A1), 17149(A1) Figure 21-1. Configuration of System Register Address 74H 75H 76H 77H 78H Window register (WR) 79H Bank register (BANK) 7AH 7BH Index register (IX) Data memory row address pointer (MP) 7CH 7DH 7EH 7FH Name Address register (AR) General register Program status word pointer (PSWORD) (RP) Symbol Bit IXH AR3 AR2 AR1 AR0 WR BANK MPH IXM IXL MPL RPH RPL PSW b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 DataNote 1 0 0 0 0 Note 2 (AR) M (IX) 0000P0000 (BANK) E (MP) 0000 (RP) BCC I CMYZ X DP E Initial 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Undefined 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 value at reset Notes 1. 2. "0" in this field means that the bit is fixed to "0". b3 and b2 of AR2 of the PD17145 (A1) are fixed to 0. b3 of AR2 of the PD17147 (A1) is fixed to 0. 75 PD17145(A1), 17147(A1), 17149(A1) Data buffer (DBF) Symbol Name DBF3 DBF2 DBF1 DBF0 Attribute MEM MEM MEM MEM Value 0.0CH 0.0DH 0.0EH 0.0FH Read/Write R/W R/W R/W R/W Bits 15 to 12 of DBF Bits 11 to 8 of DBF Bits 7 to 4 of DBF Bits 3 to 0 of DBF Description Port register Symbol Name P0A3 P0A2 P0A1 P0A0 P0B3 P0B2 P0B1 P0B0 P0C3 P0C2 P0C1 P0C0 P0D3 P0D2 P0D1 P0D0 P0E3 P0E2 P0E1 P0E0 P0F1 P0F0 Attribute FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG Value 0.70H.3 0.70H.2 0.70H.1 0.70H.0 0.71H.3 0.71H.2 0.71H.1 0.71H.0 0.72H.3 0.72H.2 0.72H.1 0.72H.0 0.73H.3 0.73H.2 0.73H.1 0.73H.0 0.6EH.3 0.6EH.2 0.6EH.1 0.6EH.0 0.6FH.1 0.6FH.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R Bit 3 of port 0A Bit 2 of port 0A Bit 1 of port 0A Bit 0 of port 0A Bit 3 of port 0B Bit 2 of port 0B Bit 1 of port 0B Bit 0 of port 0B Bit 3 of port 0C Bit 2 of port 0C Bit 1 of port 0C Bit 0 of port 0C Bit 3 of port 0D Bit 2 of port 0D Bit 1 of port 0D Bit 0 of port 0D Bit 3 of port 0E Bit 2 of port 0E Bit 1 of port 0E Bit 0 of port 0E Bit 1 of port 0F Bit 0 of port 0F Description 76 PD17145(A1), 17147(A1), 17149(A1) Register file (control registers) Symbol Name SP SIOTS SIOHIZ SIOCK1 SIOCK0 WDTRES WDTEN TM1OSEL SIOEN P0EGPU P0BGPU P0AGPU P0DBPU3 P0DBPU2 P0DBPU1 P0DBPU0 INT TM0EN TM0RES TM0CK1 TM0CK0 TM1EN TM1RES TM1CK1 TM1CK0 BTMISEL BTMRES BTMCK1 BTMCK0 P0C3IDI P0C2IDI P0C1IDI P0C0IDI P0CBIO3 P0CBIO2 P0CBIO1 P0CBIO0 IEGMD1 IEGMD0 Attribute MEM FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG Value 0.81H 0.82H.3 0.82H.2 0.82H.1 0.82H.0 0.83H.3 0.83H.0 0.8BH.3 0.8BH.0 0.8CH.2 0.8CH.1 0.8CH.0 0.8DH.3 0.8DH.2 0.8DH.1 0.8DH.0 0.8FH.0 0.91H.3 0.91H.2 0.91H.1 0.91H.0 0.92H.3 0.92H.2 0.92H.1 0.92H.0 0.93H.3 0.93H.2 0.93H.1 0.93H.0 0.9BH.3 0.9BH.2 0.9BH.1 0.9BH.0 0.9CH.3 0.9CH.2 0.9CH.1 0.9CH.0 0.9FH.1 0.9FH.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Stack pointer Serial interface start flag P0D1/SO pin function select flag Bit 1 of serial clock select flag Bit 0 of serial clock select flag Watchdog timer reset flag Watchdog timer enable flag P0D3/TM1OUT pin function select flag Serial interface enable flag P0E group pull-up select flag (pull-up = 1) P0B group pull-up select flag (pull-up = 1) P0A group pull-up select flag (pull-up = 1) P0D3 pull-up select flag (pull-up = 1) P0D2 pull-up select flag (pull-up = 1) P0D1 pull-up select flag (pull-up = 1) P0D0 pull-up select flag (pull-up = 1) INT pin status flag Timer 0 enable flag Timer 0 reset flag Bit 1 of timer 0 count pulse select flag Bit 0 of timer 0 count pulse select flag Timer 1 enable flag Timer 1 reset flag Bit 1 of timer 1 count pulse select flag Bit 0 of timer 1 count pulse select flag Basic interval timer interrupt request clock select flag Basic interval timer reset flag Bit 1 of basic interval timer count pulse select flag Bit 0 of basic interval timer count pulse select flag P0C3 input port disable flag (selects ADC3/P0C3 pin function) P0C2 input port disable flag (selects ADC2/P0C2 pin function) P0C1 input port disable flag (selects ADC1/P0C1 pin function) P0C0 input port disable flag (selects ADC0/P0C0 pin function) P0C3 input/output select flag (1 = output port) P0C2 input/output select flag (1 = output port) P0C1 input/output select flag (1 = output port) P0C0 input/output select flag (1 = output port) Bit 1 of INT pin edge detection select flag Bit 0 of INT pin edge detection select flag Description 77 PD17145(A1), 17147(A1), 17149(A1) Register file (control registers) Symbol Name ADCSTRT ADCSOFT ADCCMP Attribute FLG FLG FLG Value 0.0A0H.0 0.0A1H.3 0.0A1H.1 Read/Write R/W R/W R Description A/D converter start flag (read: always "0") A/D converter mode select flag (1 = single mode) A/D converter comparator comparison result flag (valid only in single mode) A/D converter conversion end flag Dummy flag Dummy flag Bit 1 of A/D converter channel select flag Bit 0 of A/D converter channel select flag P0D3 input/output select flag (1 = output port) P0D2 input/output select flag (1 = output port) P0D1 input/output select flag (1 = output port) P0D0 input/output select flag (1 = output port) P0E group input/output select flag (1 = all P0E as output port) P0B group input/output select flag (1 = all P0B as output port) P0A group input/output select flag (1 = all P0A as output port) Serial interface interrupt enable flag Basic interval timer interrupt enable flag Timer 1 interrupt enable flag Timer 0 interrupt enable flag INT pin interrupt enable flag Serial interface interrupt request flag Basic interval timer interrupt request flag Timer 1 interrupt request flag Timer 0 interrupt request flag INT pin interrupt request flag ADCEND ADCCH3 ADCCH2 ADCCH1 ADCCH0 P0DBIO3 P0DBIO2 P0DBIO1 P0DBIO0 P0EGIO FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG 0.0A1H.0 0.0A2H.3 0.0A2H.2 0.0A2H.1 0.0A2H.0 0.0ABH.3 0.0ABH.2 0.0ABH.1 0.0ABH.0 0.0ACH.2 R R/W R/W R/W R/W R/W R/W R/W R/W R/W P0BGIO FLG 0.0ACH.1 R/W P0AGIO FLG 0.0ACH.0 R/W IPSIO IPBTM IPTM1 IPTM0 IP IRQSIO IRQBTM IRQTM1 IRQTM0 IRQ FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG 0.0AEH.0 0.0AFH.3 0.0AFH.2 0.0AFH.1 0.0AFH.0 0.0BBH.0 0.0BCH.0 0.0BDH.0 0.0BEH.0 0.0BFH.0 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 78 PD17145(A1), 17147(A1), 17149(A1) Peripheral hardware registers Symbol Name SIOSFR TM0M TM1M ADCR TM0TM1C AR Attribute DAT DAT DAT DAT DAT DAT Value 01H 02H 03H 04H 45H 40H Read/Write R/W W W R/W R R/W Description Peripheral address of shift register Peripheral address of timer 0 modulo register Peripheral address of timer 1 modulo register Peripheral address of A/D converter data register Peripheral address of timer 0 timer 1 count register Peripheral address of address register for GET/PUT/ PUSH/CALL/BR/MOVT/INC instruction Others Symbol Name DBF IX Attribute DAT DAT Value 0FH 01H Description Fixed operand value of PUT, GET, and MOVT instructions Fixed operand value of INC instruction 79 PD17145(A1), 17147(A1), 17149(A1) Figure 21-2. Configuration of Control Register Column address Row address Item 0 1 S P 2 S SS SW I II ID OOOOT THCCR0 S IKKE Z10S 1 0 0 0 0 0 0 3 W D T 0E N 4 5 6 7 Symbol 0 (8) At reset 0 0 1 0 0 0 Read/ Write T M 0 E N R/W R/W R/W Symbol 1 (9) At reset T M 0 R E S 0 T M 0 C K 1 0 T M 0 C K 0 0 T M 1 E N T M 1 R E S 0 T M 1 C K 1 0 T BBBB MTTTT 1 MMMM C IRCC KSEKK 0 ES10 L 0 0 0 0 0 0 1 Read/ Write A D C 00S T R T 0 0 0 R/W R/W R/W Symbol 2 (A) At reset 0 A AA D DD C CC S0CE O MN F PD T 0 0 0 R 0 A D C C H 3 0 A D C C H 2 0 A D C C H 1 0 A D C C H 0 0 0 Read/ Write R/W R/W R/W Symbol 3 (B) At reset Read/ Write Remark ( ) is the address when the assembler (AS17K) is used. All the flags of the control register are registered to the device file as assembler reserved words, and are convenient for program development. 80 PD17145(A1), 17147(A1), 17149(A1) Figure 21-2. Configuration of Control Register 8 9 A T M 1 O0 S E L 0 0 B C S PP I 00 O EB 0E0GG N PP UU 0 0 0 0 0 P 0 A G P U 0 P 0 D B P U 3 0 P 0 D B P U 2 0 D P 0 D B P U 1 0 P 0 D B P U 0 0 E F I N T 0 0 0 0 0 R 0 Note R/W R/W R/W P 0 C 3 I D I 0 P 0 C 2 I D I 0 P 0 C 1 I D I 0 P 0 C 0 I D I 0 P 0 C B I O 3 0 P 0 C B I O 2 0 P 0 C B I O 1 0 P 0 C B I O 0 0 0 I E G 0M D 1 0 0 I E G M D 0 0 0 R/W R/W R/W P 0 D B I O 3 0 P 0 D B I O 2 0 P 0 D B I O 1 0 P P 0 0 D E B0G I I O O 0 0 0 0 P 0 B G I O 0 P 0 A G I O 0 0 0 I P S 0I O I P B T M I P T M 1 II PP T M 0 0 0 0 0 0 0 0 0 R/W R/W R/W R/W 0 0 I R Q 0S0 I O 0 0 0 0 I R Q 0B0 T M 0 1 0 0 I R Q 0T0 M 1 0 1 0 0 I R Q 0T0 M 0 0 0 0 I R Q 0 0 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W Note INT flag differs depending on the status of the INT pin at that time. 81 PD17145(A1), 17147(A1), 17149(A1) 22. ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings (Ta = 25 C) Parameter Supply voltage A/D converter reference voltage Input voltage Output voltage Symbol VDD VREF VI VO Per P0A, P0B, or P0C High-level output current IOHNote Total of P0A, P0B, and P0C Per P0A, P0B, or P0C Peak value Effective value Peak value Effective value Per P0D or P0E Low-level output current IOLNote Effective value Total of P0A, P0B, P0C, P0D, and P0E Operating temperature Storage temperature Power dissipation Topt Tstg Pd Ta = 85 C 28-pin plastic shrink DIP 28-pin plastic SOP Peak value Effective value 15 100 50 -40 to +110 -65 to +150 140 85 mA mA mA C C mW mW Peak value -30 -15 15 7.5 30 mA mA mA mA mA Peak value Effective value P0A, P0B, P0C, P0D, P0E, P0F, INT, RESET, XIN -0.3 to VDD + 0.3 -15 -7.5 V mA mA Condition Ratings -0.3 to +7.0 -0.3 to VDD + 0.3 -0.3 to VDD + 0.3 Unit V V V Note Caution [Effective value] = [Peak value] x Duty If the value of even one of the above parameters is exceeded even momentarily, the quality of the product may be degraded. The absolute maximum ratings are the values exceeding which may physically damage the product. Be sure to use the product with these values not exceeded. Recommended Supply Voltage Range (Ta = -40 to +110 C) Parameter Symbol Condition CPU (other than A/D converter and POC circuit) Supply voltage VDD A/D converter fx = 400 kHz to 2 MHz fx = 400 kHz to 4 MHz fx = 400 kHz to 8 MHz Absolute accuracy: 1.5LSB, 2.5 V VREF VDD fx = 400 kHz to 4 MHz MIN. 2.7 3.6 4.5 TYP. MAX. 5.5 5.5 5.5 Unit V V V 4.0 5.5 V POC circuit (mask option) 4.5 5.5 V 82 PD17145(A1), 17147(A1), 17149(A1) DC Characteristics (VDD = 2.7 to 5.5 V, Ta = -40 to +110 C) Parameter Symbol VIH1 Input voltage, high VIH2 VIH3 VIL1 Input voltage, low VIL2 VIL3 Condition P0A, P0B, P0C, P0D, P0E, P0F RESET, SCK, SI, INT XIN P0A, P0B, P0C, P0D, P0E, P0F RESET, SCK, SI, INT XIN 4.5 VDD 5.5 IOH = -1.0 mA Output voltage, high VOH P0A, P0B, P0C 2.7 VDD < 4.5 IOH = -0.5 mA 4.5 VDD 5.5 IOL = 1.0 mA VOL1 Output voltage, low P0D, P0E IOL = 15 mA Input leakage current, high Input leakage current, low Output leakage current, high Output leakage current, low Internal pull-up resistorNote 1 ILIH ILIL ILOH ILOL RPULL P0D fx = 8.0 MHz fx = 4.0 MHz IDD1 Operation mode fx = 2.0 MHz fx = 400 kHz fx = 8.0 MHz fx = 4.0 MHz IDD2 HALT mode fx = 2.0 MHz fx = 400 kHz VDD = 5 V 10 % VDD = 5 V 10 % VDD = 3 V 10 % VDD = 5 V 10 % VDD = 3 V 10 % VDD = 5 V 10 % VDD = 5 V 10 % VDD = 3 V 10 % VDD = 5 V 10 % VDD = 3 V 10 % 3 10 2.0 1.4 0.5 0.9 0.3 1.0 0.9 0.3 0.7 0.3 3.0 2.0 30 4.5 3.3 1.5 1.7 1.0 2.0 1.9 1.0 1.5 0.9 30 30 k mA mA mA mA mA mA mA mA mA mA P0A, P0B, P0C, P0D, P0E 2.7 VDD < 4.5 IOL = 0.5 mA VOL2 4.5 VDD 5.5 2.7 VDD < 4.5 VIN = VDD VIN = 0 V VOUT = VDD VOUT = 0 V 50 100 1.0 2.0 5 -5 5 -5 250 V V 0.3 V 0.3 V VDD - 0.3 V MIN. 0.7VDD 0.8VDD VDD - 0.5 0 0 0 VDD - 0.3 TYP. MAX. VDD VDD VDD 0.3VDD 0.2VDD 0.4 Unit V V V V V V V P0A, P0B, P0C, P0D, P0E, P0F P0A, P0B, P0C, P0D, P0E, P0F P0A, P0B, P0C, P0D, P0E P0A, P0B, P0C, P0D, P0E P0A, P0B, P0E, P0F, RESET, INT A A A A k Supply current Note 2 IDD3 STOP mode VDD = 5 V 10 % VDD = 3 V 10 % A A Notes 1. 2. The pull-up resistors of P0F, RESET, and INT are mask options. Excluding the current of the A/D converter and POC circuit, and the current flowing into the internal pull-up resistor. 83 PD17145(A1), 17147(A1), 17149(A1) AC Characteristics (VDD = 2.7 to 5.5 V, Ta = -40 to +110 C) Parameter CPU clock cycle time (instruction execution time) INT input frequency f INT (TM0 count clock input) INT high-, low-level width (external interrupt input) RESET low-level width t INTH, t INTL VDD = 4.5 to 5.5 V t RSL 50 RLS low-level width t RLSL VDD = 4.5 to 5.5 V 10 50 VDD = 4.5 to 5.5 V 10 50 10 0 400 kHz Symbol VDD = 4.5 to 5.5 V t CY VDD = 3.6 to 5.5 V Condition MIN. 1.9 3.9 7.9 TYP. MAX. 41 41 41 Unit s s s s s s s s s Remark t CY = 16/fx (fx: system clock oscillation frequency) Interrupt input timing t INTL t INTH INT RESET input timing t RSL RESET RLS input timing t RLSL RLS 84 PD17145(A1), 17147(A1), 17149(A1) Serial transfer operation (VDD = 2.7 to 5.5 V, Ta = -40 to +110 C) Parameter Symbol Input 10 RL = 1 k, SCK cycle time t KCY CL = 100 pF Output Internal pull-up, CL = 100 pF VDD = 4.5 to 5.5 V Input 5.0 SCK high-, low-level width t KH, t KL Output Internal pull-up, CL = 100 pF SI setup time (to SCK ) SI hold time (from SCK ) tSIK t KSI VDD = 4.5 to 5.5 V RL = 1 k, CL = 100 pF SO output delay time from SCK t KSO Internal pull-up, CL = 100 pF VDD = 4.5 to 5.5 V 14 26 1.4 VDD = 4.5 to 5.5 V t KCY/2 - 12 t KCY/2 - 24 Condition VDD = 4.5 to 5.5 V MIN. 2.0 TYP. MAX. Unit s s s s s s s s s s s s ns ns 0.8 VDD = 4.5 to 5.5 V 2.0 8 VDD = 4.5 to 5.5 V 32 64 1.0 RL = 1 k, CL = 100 pF VDD = 4.5 to 5.5 V t KCY/2 - 0.6 t KCY/2 - 1.2 100 100 s s s s Remark RL: load resistance of output line CL: load capacitance of output line VDD RL Output line CL Serial transfer timing t KCY t KL t KH SCK t SIK t KSI SI Input data t KSO SO Output data 85 PD17145(A1), 17147(A1), 17149(A1) A/D Converter (VDD = 4.0 to 5.5 V, Ta = -40 to +110 C) Parameter Resolution Absolute accuracy Conversion time Note 1 Symbol Condition MIN. 8 TYP. 8 MAX. 8 1.5 25 t CY Unit bit LSB 2.5 V VREF VDD t CONV VADIN VREF I ADC I REF When A/D converter operates 0 2.5 1.0 0.1 Note 2 s V V mA mA Analog input voltage Reference input voltage A/D converter circuit current VREF pin current VREF VDD 2.0 0.3 Notes 1. 2. Absolute accuracy excluding quantization error (0.5LSB) Time since a conversion start instruction has been executed until conversion ends (ADCEND = 1) (50 s at 8 MHz). Remark tCY = 16/fx (fx: system clock oscillation frequency) POC Circuit (mask option Note 1) (VDD = 2.7 to 5.5 V, Ta = -40 to +110 C) Parameter POC detection voltageNote 2 Supply voltage fall speed Reset detection pulse width POC circuit current Symbol VPOC t POCS t SAMP IPOC 1 3.0 10 Condition MIN. 3.6 TYP. 4.0 MAX. 4.45 0.08 Unit V V/ms ms A Notes 1. 2. The POC circuit can be used in an application circuit that operates at VDD = 4.5 to 5.5 V, fx = 400 kHz to 4 MHz. This is the voltage at which the POC circuit clears its internal reset operation. The internal reset is cleared when VPOC < VDD. 86 PD17145(A1), 17147(A1), 17149(A1) Oscillator Characteristics (VDD = 2.7 to 5.5 V, Ta = -40 to +110 C) Resonator Note Symbol Condition MIN. 0.39 Ceramic resonator Oscillation frequency VDD = 3.6 to 5.5 V VDD = 4.5 to 5.5 V 0.39 0.39 TYP. MAX. 2.04 4.08 8.16 Unit MHz MHz MHz Note Do not use a resonator whose oscillation growth time exceeds 2 ms. Recommended Ceramic Resonator (Ta = -40 to +110 C) Manufacturer Recommended Constants C1 [pF] CSB400JA CSA2.00MGA040 CST2.00MGA040 Murata Mfg. Co. CSA4.00MGA CST4.00MGWA CSA8.00MTZA CST8.00MTWA 220 100 C2 [pF] 220 100 Rd [k] 5.6 0 0 0 0 0 0 Operating Supply Voltage [V] MIN. 2.7 2.7 2.7 3.6 3.6 4.5 4.5 MAX. 5.5 5.5 5.5 5.5 5.5 5.5 5.5 For automotive electronics Part Number Remark Unnecessary (C-contained type) 30 30 Unnecessary (C-contained type) 30 30 Unnecessary (C-contained type) External Circuit Example XIN XOUT Rd C1 C2 87 PD17145(A1), 17147(A1), 17149(A1) 23. CHARACTERISTIC CURVE (REFERENCE VALUE) 4.0 (Ta = 25 C) XIN C1 3.0 XOUT C2 CSA 8.00MTZA (C1 = C2 = 30 pF) CSA 4.00MGA (C1 = C2 = 30 pF) CSA 2.00MGA040 (C1 = C2 = 100 pF) Operation mode (8 MHz) Supply current IDD [mA] 2.0 Operation mode (4 MHz) Operation mode (2 MHz) HALT mode (8 MHz) 1.0 HALT mode (2 MHz) HALT mode (4 MHz) 2.7 0 2.0 3.0 3.6 4.0 5.0 5.5 Supply voltage VDD [V] IOL vs. VOL Characteristic Example 1 (P0A, P0B, P0C) 20 (Ta = 25 C) 15 VDD = 5.0 V VDD = 4.5 V VDD = 3.5 V Low-level output current I OL [mA] 10 5 0 1 2 3 Low-level output voltage V OL [V] Caution The absolute maximum rating is 15 mA (peak value) per pin. 88 PD17145(A1), 17147(A1), 17149(A1) IOL vs. VOL Characteristics Example 2 (P0D, P0E) (Ta = 25 C) 30 VDD = 5.0 V VDD = 4.5 V Low-level output current IOL [mA] VDD = 3.5 V 20 10 0 1 2 Low-level output voltage VOL [V] Caution The absolute maximum rating is 30 mA (peak value) per pin. IOH vs. (VDD - VOH) Characteristic Example (Ta = 25 C) - 20 VDD = 5.0 V - 15 High-level output current IOH [mA] VDD = 4.5 V VDD = 3.5 V - 10 -5 0 1 VDD - VOH [V] 2 3 Caution The absolute maximum rating is -15 mA (peak value) per pin. 89 PD17145(A1), 17147(A1), 17149(A1) 24. PACKAGE DRAWINGS 28 PIN PLASTIC SHRINK DIP (400 mil) 28 15 1 A 14 K I L J G H F D N M C B M R NOTES 1) Each lead centerline is located within 0.17 mm (0.007 inch) of its true position (T.P.) at maximum material condition. 2) Item "K" to center of leads when formed parallel. ITEM A B C D F G H I J K L M N R MILLIMETERS 28.46 MAX. 2.67 MAX. 1.778 (T.P.) 0.500.10 0.85 MIN. 3.20.3 0.51 MIN. 4.31 MAX. 5.08 MAX. 10.16 (T.P.) 8.6 0.25 +0.10 -0.05 0.17 0~15 INCHES 1.121 MAX. 0.106 MAX. 0.070 (T.P.) 0.020 +0.004 -0.005 0.033 MIN. 0.1260.012 0.020 MIN. 0.170 MAX. 0.200 MAX. 0.400 (T.P.) 0.339 0.010 +0.004 -0.003 0.007 0~15 S28C-70-400B-1 Caution The ES model differs from the mass-produced model in terms of outline dimensions and materials. Refer to the drawing of the ES model. 90 PD17145(A1), 17147(A1), 17149(A1) 28 PIN PLASTIC SOP (375 mil) 28 15 detail of lead end 1 A 14 H 3 +7 -3 G I J F E K C D MM B N L P28GT-50-375B-1 NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition. ITEM A B C D E F G H I J K L M N MILLIMETERS 18.2 MAX. 0.845 MAX. 1.27 (T.P.) 0.40+0.10 -0.05 0.125 0.075 2.9 MAX. 2.50 0.2 10.3 0.3 7.2 0.2 1.6 0.2 0.15+0.10 -0.05 0.8 0.2 0.12 0.10 INCHES 0.717 MAX. 0.034 MAX. 0.050 (T.P.) 0.016+0.004 -0.003 0.005 0.003 0.115 MAX. 0.098+0.009 -0.008 0.406+0.012 -0.013 0.283+0.009 -0.008 0.063 0.008 0.006+0.004 -0.002 0.031+0.009 -0.008 0.005 0.004 Caution The ES model differs from the mass-produced model in terms of outline dimension and materials. Refer to the drawing of the ES model. 91 PD17145(A1), 17147(A1), 17149(A1) 28 PIN CERAMIC SHRINK DIP (400 mil) (For ES) 28 15 1 A 14 K L J G H I F D N M C B M R NOTES 1) Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. 2) ltem "K" to center of leads when formed parallel. ITEM A B C D F G H I J K L M N R MILLIMETERS 28.0 MAX. 5.1 MAX. 1.778 (T.P.) 0.460.05 0.8 MIN. 3.01.0 1.0 MIN. 2.7 4.3 MAX. 10.16 (T.P.) 9.84 0.250.05 0.25 0~15 INCHES 1.103 MAX. 0.201 MAX. 0.070 (T.P.) 0.0180.002 0.031 MIN. 0.1180.04 0.039 MIN. 0.106 0.170 MAX. 0.400 (T.P.) 0.387 0.010 +0.002 -0.003 0.010 0~15 P28D-70-400B-1 92 PD17145(A1), 17147(A1), 17149(A1) 28 PIN CERAMIC SOP (For ES) A C T2 D J1 I NOTE The lengths of leads ( 1 ) and the height of potting ( 2 ) are not to be specified because the lead cutting process and the potting process are not controlled. ITEM A C D G I J K T MILLIMETERS 18.00.2 1.27 (T.P.) 0.40.05 1.520.15 8.40.15 16.4 0.150.025 1.0 INCHES 0.709 +0.008 -0.009 0.05 (T.P.) +0.002 0.016 -0.003 0.060.006 0.331+0.006 -0.007 0.646 0.0060.001 0.039 X28B-50B1 K G 93 PD17145(A1), 17147(A1), 17149(A1) 25. RECOMMENDED SOLDERING CONDITIONS Solder this product under the following recommended conditions. For details of the recommended soldering conditions, refer to Information Document Semiconductor Device Mounting Technology Manual (C10535E). For the other soldering conditions and methods, consult NEC. Table 25-1. Soldering Conditions of Surface Mount Type PD17145GT(A1)-xxx: 28-pin plastic SOP (375 mil) PD17147GT(A1)-xxx: 28-pin plastic SOP (375 mil) PD17149GT(A1)-xxx: 28-pin plastic SOP (375 mil) Symbol of Recommended Condition Package peak temperature: 235 C, Time: 30 seconds max. (210 C min.), Number of times: 2 max., Duration Note : 7 (after that, prebaking is necessary for 20 hours at 125 C.) Soldering Method Soldering Condition Note Caution Number of storage days after the dry pack was opened. Storage conditions: 25 C, 65 %RH max. Do not use two or more soldering methods in combination (except pin partial heating). 94 PD17145(A1), 17147(A1), 17149(A1) Table 25-2. Soldering Conditions of Insertion Type PD17145CT(A1)-xxx: 28-pin plastic shrink DIP (400 mil) PD17147CT(A1)-xxx: 28-pin plastic shrink DIP (400 mil) PD17149CT(A1)-xxx: 28-pin plastic shrink DIP (400 mil) Soldering Method Wave soldering (pin only) Pin partial heating Soldering Condition Solder bath temperature: 260 C max., Time: 10 seconds max. Pin temperature: 300 C max., Time: 3 seconds max. (per side of pin) Caution When performing wave soldering, exercise care that only the pins are wetted with solder and that no part of the package must be wetted. 95 PD17145(A1), 17147(A1), 17149(A1) APPENDIX A. FUNCTION COMPARISON BETWEEN PD17145 SUBSERIES AND THE PD17135A AND 17137A PD17145 ROM RAM Stack 2 KB PD17147 4 KB 110 x 4 bits PD17149 8 KB PD17135A 2 KB PD17137A 4 KB 112 x 4 bits Address stack x 5 levels Interrupt stack x 3 levels Instruction execution time (clock, operating voltage) 2 s (8 MHz, 4.5 to 5.5 V) 4 s (4 MHz, 3.6 to 5.5 V) 8 s (2 MHz, 2.7 to 5.5 V) 12 (P0A, P0B, P0C) 2 (P0F0, P0F1) 1 (INT) Can be pulled up by mask option 2 s (8 MHz, 4.5 to 5.5 V) 4 s (4 MHz, 2.7 to 5.5 V) CMOS I/O Input Sense input I/O N-ch open-drain I/O 1 (P1B0) 1 (INT) 8 (P0D, P0E voltage: VDD) P0D pull-up: software P0E pull-up: software 100 k TYP. (except P0D) 10 k TYP. (P0D) 8 (P0D, P1A voltage: 9 V) P0D pull-up: mask option P1A pull-up: mask option 100 k TYP. Internal pull-up resistor A/D converter (operating voltage) Reference voltage pin 8-bit (TM0, TM1) 8 bits x 4 channels (VDD = 4.0 to 5.5 V) VREF (VREF = 2.5 V to VDD) 2 (timer output: TM1OUT) TM0 clock: system clock/512 system clock/64 system clock/16 INT TM1 clock: system clock/8192 system clock/128 system clock/16 TM0 count up 1 (also used as Count clock: system system system system watchdog timer) clock/16384 clock/4096 clock/512 clock/16 1 8 bits x 4 channels (VDD = 4.5 to 5.5 V) None (VREF = VADC = VDD) 2 (timer output: TM0OUT) TM0 clock: system clock/256 system clock/64 system clock/16 INT TM1 clock: system clock/1024 system clock/512 system clock/256 TM0 count up 1 (also used as watchdog timer) Count clock: system clock/8192 system clock/4096 TM0 count up INT 1 (with AC zero cross detection) Timer Basic interval (BTM) Interrupt External Internal SIO Output latch Standby function 4 (TM0, TM1, BTM, SIO) 1 (clocked 3-wire) Independent of P0D1 latch HALT, STOP (can be released by RLS input pin) Shared with P0D1 latch HALT, STOP 96 PD17145(A1), 17147(A1), 17149(A1) PD17145 Oscillation stabilization wait time POC function Package PD17147 128 x 256 counts Mask option PD17149 PD17135A PD17137A 512 x 256 counts Internal 28-pin plastic SDIP (400 mil) 28-pin plastic SOP (375 mil) One-time PROM PD17P149 PD17P137A Caution The PD17145 subseries is not pin-compatible with the PD17135A and 17137A. The PD17145 subseries does not include a product equivalent to the PD17134A and 17136A (RC oscillation type). For the electrical specifications of each product, refer to the Data Sheet of the product. 97 PD17145(A1), 17147(A1), 17149(A1) APPENDIX B. DEVELOPMENT TOOLS The following development tools are available for developing programs for the PD17145(A1), 17147(A1), and 17149(A1): Hardware Name Outline IE-17K, IE-17K-ET, and EMU-17K are in-circuit emulators that can be used with any products in the 17K series. IE-17K and IE-17K-ET are connected to PC-9800 series or IBM PC/ATTM as the host machine with RS-232-C. EMU-17K is inserted into an expansion slot of the PC-9800 series. These in-circuit emulators operate as the emulator for a device when used in combination with the dedicated system evaluation board (SE board) of the device. When man-machine interface, SIMPLEHOSTTM, is used a sophisticated debugging environment can be realized. EMU-17K also has a function that allows real-time monitoring of the contents of the data memory. SE-17145 is an SE board for the PD17145 subseries. It can be used alone to evaluate the system, or in combination with an in-circuit emulator for debugging. EP-17K28CT is an emulation probe for the 17K series 28-pin shrink DIP (400 mil). In-circuit emulator IE-17K, IE-17K-ET Note 1, EMU-17K Note 2 SE board (SE-17145) Emulation probe (EP-17K28CT) Emulation probe (EP-17K28GT) Conversion adapter (EV-9500GT-28 Note 3) PROM programmer (AF-9703, AF-9704, AF-9705 or AF-9706) Note 4 EP-17K28GT is an emulation probe for the 17K series 28-pin SOP (375 mil). It connects the SE board and target system when used with EV-9500GT-28Note 3. EV-9500GT-28 is an adapter for the 28-pin SOP (375 mil). It is used to connect EP17K28GT and target system. AF-9703, AF-9704, AF-9705, and AF-9706 are PROM programmers supporting the PD17P149. By connecting programmer adapter AF-9808M to these programmers, the PD17P149 can be programmed. AF-9808M is an adapter used to program the PD17P149, in combination with AF9703, AF-9704, AF-9705, or AF-9706. Programmer adapter Note 4 (AF-9808M) Notes 1. 2. 3. 4. Low-cost model: external power supply type This is a product of IC Corporation. For details, consult IC Corporation (Tokyo (03) 3447-3793). Two EV-97500GT-28s are supplied with the EP-17K28GT. Five EV-9500GT-28s are separately available as a set. These are products of Ando Electric Corporation. For details, consult Ando Electric Corporation (Tokyo (03) 3733-1151). 98 PD17145(A1), 17147(A1), 17149(A1) Software Supply Media 5"2HD MS-DOSTM 3.5"2HD 5"2HC IBM PC/AT PC DOSTM 3.5"2HC 5"2HD MS-DOS 3.5"2HD 5"2HC IBM PC/AT PC DOS 3.5"2HC 5"2HD MS-DOS 3.5"2HD Windows 5"2HC IBM PC/AT PC DOS 3.5"2HC Name Outline AS17K is an assembler that can be used with any products in the 17K series. To develop the program of the PD17145(A1), 17147(A1), and 17149(A1), the AS17K and a device file (AS17145, AS17147, or AS17149) are used in combination. AS17145, AS17147, and AS17149 are device files for the PD17145(A1), 17147(A1), 17149(A1), and PD17P149. They can be used in combination with the assembler for the 17K series (AS17K). Host Machine OS Order Code 17K series assembler (AS17K) PC-9800 series S5A10AS17K S5A13AS17K S7B10AS17K S7B13AS17K S5A10AS17145Note S5A13AS17145Note S7B10AS17145Note S7B13AS17145Note S5A10IE17K S5A13IE17K S7B10IE17K S7B13IE17K Device file AS17145, AS17147, AS17149 PC-9800 series Support software (SIMPLEHOST) SIMPLEHOST is software that serves as man-machine interface on WindowsTM when a program is developed by using an in-circuit emulator and a personal computer. PC-9800 series Note Remark SxxxxAS17145 includes AS17145, AS17147, and AS17149. The version of the OS supported is as follows: OS MS-DOS PC DOS Windows Version Ver. 3.30 to Ver. 5.00A Note Ver. 3.1 to Ver. 5.0Note Ver. 3.0 to Ver. 3.1 Note Although MS-DOS Ver.5.00/5.00A and PC DOS Ver. 5.0 have a task swap function, this function cannot be used with this software. 99 PD17145(A1), 17147(A1), 17149(A1) NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS device behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. 100 PD17145(A1), 17147(A1), 17149(A1) Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, please contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: * Device availability * Ordering information * Product release schedule * Availability of related technical literature * Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) * Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. NEC Electronics Inc. (U.S.) Santa Clara, California Tel: 408-588-6000 800-366-9782 Fax: 408-588-6130 800-729-9288 NEC Electronics (Germany) GmbH Benelux Office Eindhoven, The Netherlands Tel: 040-2445845 Fax: 040-2444580 NEC Electronics Hong Kong Ltd. Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044 NEC Electronics Hong Kong Ltd. NEC Electronics (France) S.A. Velizy-Villacoublay, France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411 NEC Electronics (Germany) GmbH Duesseldorf, Germany Tel: 0211-65 03 02 Fax: 0211-65 03 490 NEC Electronics (France) S.A. NEC Electronics (UK) Ltd. Milton Keynes, UK Tel: 01908-691-133 Fax: 01908-670-290 Spain Office Madrid, Spain Tel: 01-504-2787 Fax: 01-504-2860 NEC Electronics Singapore Pte. Ltd. United Square, Singapore 1130 Tel: 253-8311 Fax: 250-3583 NEC Electronics Taiwan Ltd. NEC Electronics Italiana s.r.1. Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99 NEC Electronics (Germany) GmbH Scandinavia Office Taeby, Sweden Tel: 08-63 80 820 Fax: 08-63 80 388 Taipei, Taiwan Tel: 02-719-2377 Fax: 02-719-5951 NEC do Brasil S.A. Cumbica-Guarulhos-SP, Brasil Tel: 011-6465-6810 Fax: 011-6465-6829 J97. 8 101 PD17145(A1), 17147(A1), 17149(A1) SIMPLEHOST is a trademark of NEC Corporation. MS-DOS and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. PC/AT and PC DOS are trademarks of IBM Corporation. The export of this product from Japan is regulated by the Japanese government. To export this product may be prohibited without governmental license, the need for which must be judged by the customer. The export or re-export of this product from a country other than Japan may also be prohibited without a license from that country. Please call an NEC sales representative. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96.5 |
Price & Availability of UPD17145
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |